Conditions for Setting the DTC
A driver select switch input error is detected when both switch inputs (connector pins C5 and C6) are asserted (grounded) or both are unasserted (open) for more than 3.0 seconds consecutively. If a driver select switch input error is detected, the system will default to the Normal switch setting, activate both position L.E.D.s, and set code 33.
Action Taken When the DTC Sets
- Record driver select switch error.
- Turn on both L.E.D.s.
- Default to Touring setting until a valid switch input combination is detected.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Is the resistance greater than 10 ohms? | ohms | Go to Step 2 | Go to Step 7 |
2 | Check the resistance in circuit 1435 from the control module to the driver select switch. Is the resistance greater than 10 ohms | ohms | Go to Step 3 | Go to Step 4 |
3 | Repair the open circuit condition in circuit 1435. Is the repair complete? | -- | ||
4 | Check the resistance in the circuit from the drivers switch to ground. Is the resistance greater than 10 ohms? | ohms | Go to Step 5 | Go to Step 6 |
5 | Repair the open circuit condition in circuit 1436. Is the repair complete? | -- | -- | |
6 | Replace the driver select switch. Is the repair complete? | -- | -- | |
7 | Measure the resistance between pins C6 and ground of wiring harness connector. Is the resistance greater than 500 ohms? | 500 ohms | Go to Step 8 | Go to Step 16 |
8 | Measure the resistance between pins C6 and D16 of wiring harness connector. Is the resistance greater than 500 ohms? | 500 ohms | Go to Step 10 | Go to Step 9 |
9 | Repair the short in circuit 1434. Is the repair complete? | -- | -- | |
10 |
Is the resistance greater than 10 ohms? | ohms | Go to Step 11 | Go to Step 19 |
11 | Check the resistance in circuit 1434 from the control module to the driver select switch. Is the resistance greater than 10 ohms? | ohms | Go to Step 12 | Go to Step 13 |
12 | Repair the open in circuit 1434. Is the repair complete? | -- | -- | |
13 | Check the resistance in the circuit from driver select switch to ground. Is the resistance greater than 10 ohms? | ohms | Go to Step 14 | Go to Step 15 |
14 | Repair the open in circuit 1436. Is the repair complete? | -- | -- | |
15 | Replace the driver select switch. Is the replacement complete? | -- | -- | |
16 |
Is the resistance greater than 500 ohms? | ohms | Go to Step 17 | Go to Step 18 |
17 | Replace the driver select switch. Is the replacement complete? | -- | -- | |
18 |
Repair the short in circuit 1434. Is the repair complete? | -- | -- | |
19 | Measure the resistance between pins C5 and ground of the wiring harness connector. Is the resistance greater than 500 ohms? | ohms | Go to Step 20 | Go to Step 23 |
20 | Measure the resistance between pins C5 and D16 of the wiring harness connector. Is the resistance greater than 500 ohms? | ohms | Go to Step 21 | Go to Step 22 |
21 | Replace the control module. Refer to Electronic Suspension Control Module Replacement . Is the replacement complete? | -- | -- | |
22 | Repair the short in circuit 1435. Is the repair complete? | -- | -- | |
23 |
Is the resistance greater than 500 ohms? | -- | Go to Step 24 | Go to Step 25 |
24 | Replace the driver select switch. Is the replacement complete? | -- | -- | |
25 | Repair the short in circuit 1435. Is the repair complete? | -- | -- |
