GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2000 🢒 Bonneville 🢒 Restraints 🢒 SIR 🢒 Instrument Panel Inflatable Restraint Module Replacement

Removal Procedure

Caution: When you are carrying an undeployed inflator module:

   • Do not carry the inflator module by the wires or connector on the inflator module
   • Make sure the bag opening points away from you
When you are storing an undeployed inflator module, make sure the bag opening points away from the surface on which the inflator module rests. When you are storing a steering column, do not rest the column with the bag opening facing down and the column vertical. Provide free space for the air bag to expand in case of an accidental deployment. Otherwise, personal injury may result.


    Object Number: 464940 Size: SH
  1. Disable the SIR system. Refer to Disabling the SIR System .
  2. Remove the right insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gauges and Console.
  3. Remove the connector position assurance (CPA) (4) from the inflatable restraint instrument panel (IP) module connector (2).
  4. Remove the yellow 2-way connector (2) on the inflatable restraint IP module from the yellow 2-way connector (1) on the vehicle harness.
  5. Remove the 2-way connector (2) from the IP bracket (3).

    6. Object Number: 464929 Size: SH
  6. Remove the IP upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges and Console.
  7. Note the IP module wire harness routing, to help in re-assembly.
  8. Push the 2-way connector (2) on the inflatable restraint IP module away from the IP (3).

    9. Object Number: 464937 Size: SH
  9. Remove the inflatable restraint IP module mounting fasteners (2).

    10. Important: When removing the IP module, do not damage the IP module pigtail (4).

  10. Remove the IP module (3) from the IP (1).
  11. Fully deploy the module before disposal. If the module was replaced under warranty, fully deploy and dispose of the module after the required retention period. Refer to Inflator Module Handling, Shipping, and Scrapping .

Installation Procedure

    Object Number: 464937 Size: SH

    Important: When installing the IP module, do not damage the inflatable restraint IP module pigtail.

  1. Route the IP module pigtail (4) down through the IP (1).
  2. Install the IP module (3) to the IP (1).

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the IP module mounting fasteners (2).

    4. Tighten
    Tighten fasteners to 9 N·m (80 lb in).


    Object Number: 464929 Size: SH
  4. Route the IP module wiring harness (2) in place. Secure the 2-way connector clip to the IP (3).
  5. Install the IP upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges and Console.

    6. Object Number: 464940 Size: SH
  6. Clip the IP module 2-way connector (2) to the IP bracket (3).
  7. Install the IP module 2-way connector (2) to the vehicle harness 2-way connector (1).
  8. Install the CPA (4) to the IP module connector (2).
  9. Install the right insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gauges and Console.
  10. Enable the SIR system. Refer to Enabling the SIR System .