Circuit Description
Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the vehicle is first started, the powertrain control module (PCM) operates in an Open Loop mode, ignoring the HO2S signal voltage when calculating the air-to-fuel ratio. The PCM supplies the HO2S with a reference or bias voltage of about 450 mV. The HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage once in Closed Loop. A high HO2S voltage output indicates a rich fuel mixture. A low HO2S voltage output indicates a lean mixture. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature, and to provide an accurate voltage signal. The HO2S 2 is used for post catalyst monitoring. If the PCM detects that the HO2S 2 voltage remains above a calibrated amount for an excessive amount of time, DTC P0138 will set.
Each HO2S 2 has the following circuits:
| • | HO2S 2 high signal |
| • | HO2S 2 low signal |
| • | HO2S 2 heater ignition 1 voltage |
| • | HO2S 2 heater ground |
Conditions for Running the DTC
| • | DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0410, P0440, P0442, P0443, P0446, P0449, or P1441 are not set. |
| • | The Air Fuel Ratio parameter is between 14.5:1-14.8:1. |
| • | The TP sensor parameter is between 3-40 percent. |
| • | The system voltage is between 9-18 volts. |
Conditions for Setting the DTC
The PCM detects that the HO2S 2 voltage is more than 975 mV, for more than 75 seconds during Closed Loop operation.
Or
The PCM detects that the HO2S 2 voltage is more than 200 mV, during decel fuel cut-off (DFCO), for more than 100 seconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
A normally functioning HO2S 2 voltage signal will fluctuate above and below the bias voltage amount. The action in the test step should result in a visible reaction from the HO2S 2 output.
-
A voltage reading other than bias voltage in this step indicates a short circuit condition in the high signal circuit.
-
The conditions listed in the table may contribute to the failure of the HO2S. The conditions listed apply only to this type of failure.
Step | Action | Values | Yes | No | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views | ||||||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||||||||
Is the HO2S 2 voltage more than the specified value? | 975 mV | Go to Step 4 | Go to Step 3 | |||||||||||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions | ||||||||||||
Is the HO2S 2 voltage more than the specified value? | 975 mV | Go to Step 5 | Go to Step 9 | |||||||||||||
5 | Measure the voltage from the high signal circuit of the HO2S 2 harness connector, on the engine harness side, to a good ground with a DMM . Is the HO2S 2 voltage above the specified value? | 5.5 V | Go to Step 7 | Go to Step 6 | ||||||||||||
Do any 5-volt reference circuit DTCs set? | -- | Go to Step 8 | Go to Step 7 | |||||||||||||
7 |
Important: Disconnection of the PCM during testing may eliminate the voltage source that caused this fault. Test the HO2S 2 high signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 | ||||||||||||
8 |
Important: Disconnection of the PCM during testing may eliminate the voltage source that caused this fault. Test the HO2S 2 high signal circuit for a short to the affected 5-volt reference circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 | ||||||||||||
9 | Inspect for the following conditions that may affect the HO2S operation: Notice: Refer to Silicon Contamination of Heated Oxygen Sensors Notice in the Preface section.
Notice: Refer to Heated Oxygen and Oxygen Sensor Notice in the Preface section.
Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 10 | ||||||||||||
10 | Test for an intermittent and for a poor connection at the harness connector of the HO2S 2. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 | ||||||||||||
11 | Test for an intermittent and for a poor connection at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 12 | ||||||||||||
12 | Replace the HO2S 2. Refer to Heated Oxygen Sensor 2 Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- | ||||||||||||
13 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- | ||||||||||||
14 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 15 | ||||||||||||
15 | Observe the Capture Info with a scan tool. Are there any DTCs that have not diagnosed? | -- | System OK | |||||||||||||
