Circuit Description
The crankshaft position (CKP) sensor is connected directly to the ignition control (IC) module. The CKP sensor consists of the following circuits:
| • | The 12-volt reference circuit |
| • | The low reference circuit |
| • | The CKP sensor 1 signal circuit |
| • | The CKP sensor 2 signal circuit |
The CKP sensor shares power supply and low reference circuits with the camshaft position (CMP) sensor. If the PCM detects no 18X reference pulses in one engine cycle, DTC P0336 sets.
Conditions for Running the DTC
The engine is running, and the 3X reference pulses are being received.
Conditions for Setting the DTC
No 18X reference pulses are received in one engine cycle, 720 degrees of crankshaft rotation.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Step | Action | Values | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views | ||||||||||||
1 | Did you perform the Diagnostic System Check - Engine Controls? | -- | Go to Step 2 | |||||||||
2 | Attempt to start the engine. Does the engine start and run? | -- | Go to Step 3 | Go to Step 8 | ||||||||
3 | Observe the 18X Crank Sensor parameter with the scan tool. Does the 18X Crank Sensor parameter change with engine speed? | -- | Go to Step 4 | Go to Step 5 | ||||||||
4 |
Does the DTC fail this ignition? | -- | Go to Step 5 | Go to Testing for Intermittent Conditions and Poor Connections | ||||||||
5 |
Does the test lamp illuminate? | -- | Go to Step 10 | Go to Step 6 | ||||||||
6 |
Does the test lamp illuminate? | -- | Go to Step 9 | Go to Step 7 | ||||||||
7 |
Does the 18X crank sensor RPM change? | -- | Go to Step 13 | Go to Step 11 | ||||||||
8 |
Is the voltage within the specified range? | 4-8 V | Go to Step 14 | Go to Step 12 | ||||||||
9 | Test the 18X reference medium resolution engine speed signal circuit between the ICM and the powertrain control module (PCM) for a short to ground. Refer to Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||||
10 | Test the 18X reference medium resolution engine speed signal circuit between the ICM and the PCM for a short to voltage. Refer to Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||||
11 | Test the 18X reference medium resolution engine speed signal circuit between the ICM and the PCM for an open. Refer to Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 16 | ||||||||
12 | Test the CKP sync signal circuit for an open. Refer to Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 15 | ||||||||
13 | Inspect for the following conditions:
Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 15 | ||||||||
14 | Test for an intermittent or for poor connections at the CKP sensor. Refer to Testing for Intermittent Conditions and Poor Connections . Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 17 | ||||||||
15 | Test for an intermittent or for poor connections at the ICM. Refer to Testing for Intermittent Conditions and Poor Connections . Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 18 | ||||||||
16 | Test for poor connections at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections . Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||||
17 | Replace the CKP sensor. Refer to Crankshaft Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||||||
18 | Replace the ICM. Refer to Ignition Control Module Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||||||
19 | Replace the PCM. Refer to Powertrain Control Module Replacement for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 20 | -- | ||||||||
20 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 21 | ||||||||
21 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |||||||||
