Exterior Trim Molding/Nameplate Replacement Z28 Fender Emblem

Removal Procedure

1. Mark the position of the emblem with a length of masking tape.
2. Remove the old emblem from the front fender.
3. Wash the fender with soapy water and wipe dry.
4. Remove all traces of adhesive from the fender using a oil-free naptha or alcohol.

Installation Procedure

1. Remove the backing paper from the emblem.
2. Measure 51.5 mm (2.03 in) from the front edge of the door to the rear edge of the emblem (1).
3. Measure 32.0 mm (1.25 in) from the bottom edge of the emblem (1) to the top edge of the molding (2).



4. Align the emblem to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Trans Am Door Emblem

Removal Procedure

1. Mark the position of the emblem with a length of masking tape.
2. Remove the old emblem from the door.
3. Wash the door with soapy water and wipe dry.
4. Remove all traces of adhesive from the door using a oil-free naptha or alcohol.

Installation Procedure

1. Remove the backing paper from the emblem.
2. Measure 40.0 mm (1.6 in) from the front edge of the door to the front edge of the emblem (2).
3. Measure 14.0 mm (0.55 in) from the top edge of the emblem (2) to the bottom edge of the molding (1).



4. Align the emblem to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Firebird/Formula Door Emblem

Removal Procedure

1. Mark the position of the emblem (1 or 2) with a length of masking tape.
2. Remove the old emblem (1 or 2) from the door.
3. Wash the door with soapy water and wipe dry.
4. Remove all traces of adhesive from the door using a oil-free naptha or alcohol.

Installation Procedure

1. Remove the backing paper from the emblem.
2. Measure 53.0 mm (2.09 in) from the front edge of the door to the front edge of the emblem (1).



3. Align the emblem to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Z28 Fender Emblem (Export)

Removal Procedure

1. Mark the position of the emblem with a length of masking tape.
2. Remove the old emblem from the door.
3. Wash the door with soapy water and wipe dry.
4. Remove all traces of adhesive from the fender using a oil-free naptha or alcohol.

Installation Procedure

1. Remove the backing paper from the emblem.
2. Measure 36.0 mm (1.42 in) from the rear edge of the fender to the rear edge of the emblem (2).
3. Measure 50.5 mm (2.0 in) from the top edge of the molding to the tope edge of the emblem (1).



4. Align the emblem to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Z28 Rear End Finish Panel

Removal Procedure

1. Mark the position of the emblem with a length of masking tape.
2. Remove the old emblem from the rear end finish panel.
3. Wash the rear fascia with soapy water and wipe dry.
4. Remove all traces of adhesive from the fascia using oil-free napthe or alcohol.

Installation Procedure

1. Remove the backing paper from the emblem.
2. Measure 164.0 mm (6.46 in) from the outer edge of the taillight lens (3) to the edge of the emblem (2).
3. Measure 16.0 mm (.63 in) from the bottom edge of the rear end finish panel (1) to the bottom edge of the emblem (2).



4. Align the emblem to the tape guideline and press firmly in place.