Circuit Description
The Mass Air Flow (MAF) sensor measures the amount of air which passes through it into the engine during a given time. The PCM uses the mass air flow information to monitor engine operating conditions for fuel delivery calculations. A large quantity of air entering the engine indicates an acceleration or high load situation, while a small quantity of air indicates deceleration or idle. The MAF sensor produces a frequency signal which can be monitored using a scan tool. The frequency will vary within a range of around 2000 Hertz at idle to about 10,000 Hertz at maximum engine load. DTC P0103 will be set if the signal frequency from the MAF sensor is higher than the possible range of a normally operating MAF sensor.
Conditions for Running the DTC
| • | The engine is running. |
| • | TP angle is less than 2.5%. |
| • | System voltage is greater than 8 volts. |
Conditions for Setting the DTC
| • | MAF signal frequency is greater than 11,500 Hertz. |
| • | Above conditions present for longer than 0.5 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the first trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed. |
| • | The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool. |
Diagnostic Aids
Check for the following conditions:
| • | Poor connection at the PCM - Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| • | Misrouted harness - Inspect the MAF sensor harness to ensure that it is not routed too close to high voltage wires such as spark plug leads. |
| • | Damaged harness - Inspect the wiring harness for damage. |
| • | If the harness appears to be OK, observe the scan tool while moving connectors and wiring harnesses related to the MAF sensor. A change in the display will indicate the location of the fault. |
If DTC P0103 cannot be duplicated, the information included in the Freeze Frame/Fail Records data can be useful in determining vehicle mileage since the DTC was last set.
Test Description
Number(s) below refer to the Step number(s) on the Diagnostic Table:
-
This step verifies if the problem is present at idle.
-
A frequency reading with the MAF sensor connector disconnected indicates an Electromagnetic Interference (EMI) related fault or a faulty connection.
-
This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must be programmed.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
Does the scan tool indicate MAF Frequency more than the specified value? | 11,500 Hz (11.5 kHz) | |||
3 |
Does the scan tool indicate this DTC failed this ignition? | -- | Go to Diagnostic Aids | |
Does scan tool indicate MAF Frequency at the specified value? | 0 Hz | |||
5 | Inspect for a faulty connection at the MAF sensor. Refer to Intermittents and Poor Connections Diagnosis and Connector Repairs . Did you find and correct the condition? | -- | ||
6 | Replace the MAF sensor. Refer to Mass Airflow Sensor Replacement . Is the replacement complete? | -- | -- | |
7 | Inspect the MAF harness for incorrect routing.
Did you find and correct the condition? | -- | ||
8 | Inspect for faulty connections of the MAF signal circuit at the PCM. Refer to Intermittents and Poor Connections Diagnosis and Connector Repairs . Did you find and correct the condition? | -- | ||
|
Important:: Replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Replace the PCM. Did you complete the replacement? | -- | -- | ||
10 |
Does the DTC reset? | -- | System OK |
