Front Lower Control Arm Bushing Replacement Front Bushing

Tools Required

1. Remove the lower control arm. Refer to Lower Control Arm Replacement .



2. Remove the lower control arm front bushing from the lower control arm (1):

2.1.	Place J 21474-3 through the large end of J 21474-6 .

2.2.	Thread J 21474-3 through the front bushing and push J 21474-3 through the open end of J 39876 .

2.3.	Place the thrust washer onto J 21474-3 with the seam facing toward the front bushing.

2.4.	Install J 39875 around the outside of the bushing in order to avoid metal distortion during removal.

2.5.	Align all tools properly with the front bushing with and the control arm (1), then install J 21474-4 and tighten until the bushing is pushed all the way out. The bushing makes a popping noise upon removal.

1. Install the lower control arm front bushing:

1.1.	Thread J 21474-3 through J 21474-5 .

1.2.	Install J 21474-3 through the new front bushing and into the lower control arm (2).

1.3.	Thread J 21474-3 and accessories into the front lower control arm.

1.4.	Install J 39876 onto J 21474-3 with the open end of J 39876 facing toward the control arm.

1.5.	Install J 39875 around the outside of the bushing in order to avoid metal distortion during installation.

1.6.	Place the thrust washer (1) onto the threaded end of J 21474-3 with the seam facing toward the control arm.

1.7.	Align all tools properly with the front bushing and the control arm, then install J 21474-4 onto J 21474-3 .

1.8.	Tighten J 21474-4 and J 21474-3 until the bushing becomes flush with the control arm.

2. Install the lower control arm. Refer to Lower Control Arm Replacement .

Front Lower Control Arm Bushing Replacement Rear Bushing

Tools Required

1. Remove the lower control arm. Refer to Lower Control Arm Replacement .



2. Remove the lower control arm rear bushing from the lower control arm (1):

2.1.	Install J 39874 onto J 21474-3 with the sealed end of J 39874 facing the head of the screw.

2.2.	Run J 21474-3 through the control arm bushing, through the control arm, and into the small end of J 39931 .

2.3.	Install the thrust washer onto J 21474-3 with the seam facing toward the control arm.

2.4.	Install J 21474-4 onto J 21474-3 . Align all parts with the control arm bushing.

2.5.	Tighten until you are able to remove the control arm bushing. The bushing may make a popping noise upon removal.

1. Install the lower control arm rear bushing:

1.1.	Secure the lower control arm (2) in a vise, then place J 21474-3 through the small end of J 39931 .

1.2.	Install J 21474-3 through the new rear bushing, then through the closed end of the rear lower control arm.

1.3.	Place the small end of J 21474-5 onto J 21474-3 .

1.4.	Install the thrust washer (1) onto J 21474-3 with the seam of the washer facing toward the control arm.

1.5.	Align all the tools with the bushing and the control arm. Set the window facing straight up and visible on J 39931 .

1.6.	Install J 21474-4 onto J 21474-3 and tighten until the rubber protrusion on the J 39931 touchesJ 39931 .

2. Install the lower control arm. Refer to Lower Control Arm Replacement .