Special Tools

Warning: Refer to Safety Glasses Warning in the Preface section.




1. Remove the cylinder head with the intake manifold and exhaust manifold attached. Refer to Cylinder Head Replacement.
2. Remove the oil pan. Refer to Oil Pan Replacement.
3. Remove the oil pump/pickup tube bolts.
4. Remove the oil pump/pickup tube.



5. Move the piston to the bottom of the piston stroke.
6. Mark the connecting rod cap.
7. Remove the connecting rod cap bolts.
8. Remove the connecting rod cap and lower connecting rod bearing.
9. Remove the upper piston connecting rod bearing.
10. Ridge ream the cylinder wall.




Warning: Handle the piston carefully. Worn piston rings are sharp and may cause bodily injury.

11. Remove the piston.
12. Use a piston ring expander tool to expand the piston rings.
13. Remove the piston rings.



14. Remove the piston pin from the piston and connecting rod assembly using the J 24086-B  (1).
15. Separate the piston from the connecting rod.

Warning: Avoid contact with moving parts and hot surfaces while working around a running engine in order to prevent physical injury.

1. Align the notch on the piston and connecting rod so that the proper sides will be facing the front of the engine.
2. Install the piston pin guide through the piston and the connecting rod.
3. Coat the piston pin with clean oil.
4. Install the piston pin into the opposite side of the piston.
5. Install the piston pin into the piston and connecting rod assembly using the J 24086-B  (1).



6. Select a set of new piston rings.
7. Measure the piston ring gap using a feeler gage. Refer to Engine Mechanical Specifications.
8. Increase the piston ring gap by carefully filing off excess material if the piston ring gap is below specifications.



9. Measure the piston ring side clearance using a feeler gage. Refer to Engine Mechanical Specifications.
10. If the piston ring is too thick, try another piston ring.
11. If no piston ring can be found that fits to specifications, the piston ring may be ground to size with emery paper placed on a sheet of glass.



12. Install a piston oil ring, the expander, then the second piston oil ring to the bottom ring groove of the piston.
13. Install the second compression ring to the middle ring groove of the piston.
14. Install the top compression ring to the top ring groove of the piston.




Caution: Use a piston ring expander to install the piston rings. The rings may be damaged if expanded more than necessary.

15. Use a piston ring expander to install the piston rings. Do not expand the piston rings beyond the expansion necessary for installation.
16. Stagger the piston oil rings (2), the oil ring rail gaps (3), the second compression ring (4), and the top compression ring in relation to the notch on the top of the piston (1).



17. Lubricate the cylinder wall and the piston rings with clean engine oil.
18. Install the piston using a ring compressor and a wood handle. Guide the lower connecting rod end to prevent damaging the crankshaft journal.
19. Install the connecting rod cap and the bearings. Refer to Crankshaft and Bearing Cleaning and Inspection.

Caution: Refer to Fastener Caution in the Preface section.




20. Install the connecting rod cap bearing bolts.

Tighten

•	Tighten the connecting rod bearing cap bolts to 25 N·m (18 lb ft).

•	Using the J 45059 or the KM-470-B  (1), tighten 1 turn of 30 degrees plus 15 degrees.




21. Install the oil pump/pickup tube.
22. Install the oil pump/pickup tube bolts.

Tighten
Tighten the oil pump/pickup tube and support bracket bolts to 10 N·m (89 lb in).

23. Install the oil pan. Refer to Oil Pan Replacement.
24. Install the cylinder head with the intake manifold and the exhaust manifold attached. Refer to Cylinder Head Replacement.