Circuit Description
The control module enables the appropriate fuel injector pulse for each cylinder. Ignition voltage is supplied to the fuel injectors. The control module controls each fuel injector by grounding the control circuit via a solid state device called a driver. The control module monitors the status of each driver. If the control module detects an incorrect voltage for the commanded state of the driver, a fuel injector control circuit DTC sets.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
| • | DTC P0201 Injector 1 Control Circuit |
| • | DTC P0202 Injector 2 Control Circuit |
| • | DTC P0203 Injector 3 Control Circuit |
| • | DTC P0204 Injector 4 Control Circuit |
Conditions for Running the DTC
| • | The engine is running. |
| • | The ignition voltage is more than 11 volts for 5 seconds. |
| • | DTC P0201-P0204 run continuously once the above conditions are met. |
Conditions for Setting the DTC
| • | The control module detects an incorrect voltage on the fuel injector control circuit. |
| • | The above condition is met for 5 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Performing the Fuel Injector Coil Test may help isolate an intermittent condition. Refer to Fuel Injector Diagnosis . |
| • | For an intermittent condition, refer to Intermittent Conditions . |
Step | Action | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views | |||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |||||||
2 |
Did the DTC fail this ignition? | Go to Step 3 | Go to Diagnostic Aids | ||||||
3 |
Does the test lamp flash when cranking the engine? | Go to Step 7 | Go to Step 4 | ||||||
4 | Does the test lamp remain illuminated at all times? | Go to Step 6 | Go to Step 5 | ||||||
5 | Test the control circuit of the fuel injector for a short to voltage or for an open between the multi-way connector and the PCM. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 14 | ||||||
6 | Test the control circuit of the fuel injector for a short to ground between the multi-way connector and the PCM. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 17 | ||||||
7 | Inspect the accessible fuel injector jumper harness between the multi-way connector and the fuel rail for the following:
Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 8 | ||||||
8 | Probe the appropriate fuel injector control circuit, fuel injector side, at the multi-way connector, with a test lamp that is connected to battery voltage. Refer to Probing Electrical Connectors. Does the test lamp illuminate? | Go to Step 15 | Go to Step 9 | ||||||
9 | With a DMM, test for continuity between the ignition 1 voltage circuit terminal and the appropriate fuel injector control circuit terminal, at the multi-way connector. Refer to Testing for Continuity. Does the DMM indicate OL? | Go to Step 10 | Go to Step 12 | ||||||
10 | Test the control circuit of the fuel injector for an open. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 11 | ||||||
11 | Test the ignition 1 voltage circuit of the fuel injector for an open between the fuel injector and the splice. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 13 | ||||||
12 | Test the control circuit of the fuel injector for a short to voltage or a short to another circuit. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 16 | ||||||
13 | Test for an intermittent and for a poor connection at the fuel injector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 16 | ||||||
14 | Test for an intermittent and for a poor connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | Go to Step 18 | Go to Step 17 | ||||||
15 | Repair the short to ground in the fuel injector control circuit. Refer to Wiring Repairs. Did you complete the repair? | Go to Step 18 | -- | ||||||
16 | Replace the affected fuel injector. Refer to Fuel Injector Replacement . Did you complete the replacement? | Go to Step 18 | -- | ||||||
17 | Replace the PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 18 | -- | ||||||
18 |
Did the DTC fail this ignition? | Go to Step 2 | Go to Step 19 | ||||||
19 | Observe the Capture Info with a scan tool. Have any other DTCs not been diagnosed? | System OK | |||||||
