Air Conditioning (A/C) System Performance Test. Pontiac G5 2007

For 1990-2009 cars only

Makes 🢒 Pontiac 🢒 2007 🢒 G5 🢒 HVAC 🢒 HVAC - Manual 🢒 Air Conditioning (A/C) System Performance Test

Air Conditioning (A/C) System Performance Test L61, LE5

Table 1:

This test measures the operating efficiency of the A/C system under the following conditions:

•	The current ambient air temperature

•	The current relative humidity

•	The high side pressure of the A/C system

•	The low side pressure of the A/C system

•	The temperature of the air being discharged into the passenger compartment

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step determines if the A/C system has at least the minimum refrigerant charge required to operate the system without damage.

This step measures the performance of the A/C system.

This step is to allow for vehicle variations as well as high ambient temperatures.

Step

Action

Values

Yes

Important:

•	The ambient air temperature must be at least 16°C (60°F) .

•	Do not induce additional air flow across the front of the vehicle during the test.

•	If you were sent here from a DTC diagnostic table, clear the DTC upon completion of this test.

Park the vehicle inside or in the shade.
Open the windows in order to ventilate the interior of the vehicle.
If the A/C system was operating, allow the A/C system to equalize for about 2 minutes.
Turn OFF the ignition.
Install the J 43600 ACR 2000 Air Conditioning Service Center.
Record the ambient air temperature displayed on the J 43600 .
Record the low and high side STATIC pressure readings.

Are both the low side and high side pressures within the specified value?

More than 16°C (60°F) - 345 kPa (50 psi)

More than 24°C (75°F) - 483 kPa (70 psi)

More than 33°C (90°F) - 690 kPa (100 psi)

Go to Step 2

Go to Leak Testing

Important: Record the relative humidity and the ambient air temperature at the time of the test.

Close the vehicle doors and windows.
Open the drivers door window 12.7-15.2 cm (5-6 in).
Select the following HVAC control settings:

•	The A/C is ON.

•	The coldest temperature setting

•	The maximum blower speed

•	Recirculation mode

•	The I/P panel outlet mode

•	All I/P panel outlets are OPEN.

Install the temperature probes of the J 43600 in the left and right center panel air outlets.
Apply the parking brake.
Place the transaxle/transmission in one of the following positions:

•	PARK (Automatic)

•	NEUTRAL (Manual)

Start the engine and warm to operating temperature.
Operate the A/C system for 5 minutes.
Inspect A/C components for the following conditions:

•	Abnormal frost areas

•	Unusual noises

Important: Press the RESET button, before using the print function of the J 43600 .

Print the following information:

•	The panel outlet air temperatures

•	The low-side pressure

•	The high-side pressure

Compare the low and high side pressures and the panel output temperatures to the A/C Performance Table below.

Does all the data recorded fall within the specified ranges of the A/C Performance Table below?

Go to Step 8

Go to Step 3

If the pressures and temperatures recorded do not fall within the specified ranges:

Continue to operate the A/C system for an additional 5 minutes.
RESET the J 43600 and record the pressures and temperatures again.
Compare the low and high side pressures and the panel output temperature to the table below.

Does all the data recorded fall within the specified ranges of the table below?

Go to Step 8

Go to Step 4

Do the high and low side pressures fall within the specified ranges, but the panel outlet temperatures do not?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone A

Go to Step 5

Is the low side pressure greater than the specified range, but the high side pressure within or less than the specified range?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone B

Go to Step 6

Are the low and high side pressures both greater than the specified ranges?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone C

Go to Step 7

Is the high side pressure greater than the specified range, but the low side pressure is within or less than the specified range?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone D

Go to Step 8

Operate the system in order to verify the test results.

Did you find the same results?

System OK

Go to Symptoms - HVAC Systems - Manual

A/C System Pressure-Zone Classification Graph

A/C Performance Table

Ambient Temperature	Relative Humidity	Low Side Service Port Pressure	High Side Service Port Pressure	Maximum Left Center Discharge Air Temperature
13-18°C (55-65°F)	0-100%	158-227 kPa (23-33 psi)	578-1012 kPa (84-147 psi)	8°C (46°F)
19-24°C (66-75°F)	Below 40%	151-220 kPa (22-32 psi)	716-1157 kPa (104-168 psi)	8°C (46°F)
19-24°C (66-75°F)	Above 40%	172-241 kPa (25-35 psi)	813-1302 kPa(118-189 psi)	10°C (50°F)
25-29°C (76-85°F)	Below 35%	172-234 kPa (25-34 psi)	999-1371 kPa (145-199 psi)	10°C (50°F)
	35-50%	179-241 kPa (26-35 psi)	1067-1433 kPa(155-208 psi)	10°C (50°F)
	Above 50%	186-248 kPa (27-36 psi)	1123-1543 kPa(163-224 psi)	12°C (52°F)
30-35°C (86-95°F)	Below 30%	186-248 kPa (27-36 psi)	1219-1619 kPa (177-235 psi)	13°C (55°F)
	30-50%	192-248 kPa (28-36 psi)	1267-1708 kPa(184-248 psi)	13°C (55°F)
	Above 50%	199-254 kPa (29-37 psi)	1350-1832 kPa (196-266 psi)	13°C (55°F)
36-41°C (96-105°F)	Below 20%	199-261 kPa (29-38 psi)	1460-1853 kPa (212-269 psi)	13°C (55°F)
	20-40%	206-261 kPa (30-38 psi)	1502-1942 kPa (218-282 psi)	14°C (57°F)
	Above 40%	206-261 kPa (30-38 psi)	1577-2032 kPa( 229-295 psi)	15°C (59°F)
42-46°C (106-115°F)	Below 20%	220-275 kPa (32-40 psi)	1722-2067 kPa (250-300 psi)	15°C (59°F)
42-46°C (106-115°F)	Above 20%	220-275 kPa (32-40 psi)	1770-2170 kPa(257-315 psi)	17°C (61°F)
47-49°C (116-120°F)	Below 30%	234-303 kPa (34-44 psi)	1991-2342 kPa (289-340 psi)	19°C (65°F)

Air Conditioning (A/C) System Performance Test RPO LSJ

Table 1:

A/C Performance Table

This test measures the operating efficiency of the A/C system under the following conditions:

•	The current ambient air temperature

•	The current relative humidity

•	The high side pressure of the A/C system

•	The low side pressure of the A/C system

•	The temperature of the air being discharged into the passenger compartment

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step determines if the A/C system has at least the minimum refrigerant charge required to operate the system without damage.

This step measures the performance of the A/C system.

This step is to allow for vehicle variations as well as high ambient temperatures.

Step

Action

Values

Yes

Important:

•	The ambient air temperature must be at least 16°C (60°F) .

•	Do not induce additional air flow across the front of the vehicle during the test.

•	If you were sent here from a DTC diagnostic table, clear the DTC upon completion of this test.

Park the vehicle inside or in the shade.
Open the windows in order to ventilate the interior of the vehicle.
If the A/C system was operating, allow the A/C system to equalize for about 2 minutes.
Turn OFF the ignition.
Install the J 43600 ACR 2000 Air Conditioning Service Center.
Record the ambient air temperature displayed on the J 43600 .
Record the low and high side STATIC pressure readings.

Are both the low side and high side pressures within the specified value?

More than 16°C (60°F) - 345 kPa (50 psi)

More than 24°C (75°F) - 483 kPa (70 psi)

More than 33°C (90°F) - 690 kPa (100 psi)

Go to Step 2

Go to Leak Testing

Important: Record the relative humidity and the ambient air temperature at the time of the test.

Close the vehicle doors and windows.
Open the driver door window 12.7-15.2 cm (5-6 in).
Select the following HVAC control settings:

•	The A/C is ON.

•	The coldest temperature setting

•	The maximum blower speed

•	Recirculation mode

•	The I/P panel outlet mode

•	All I/P panel outlets are OPEN.

Install the temperature probes of the J 43600 in the left and right center panel air outlets.
Apply the parking brake.
Place the transaxle/transmission in one of the following positions:

•	PARK (Automatic)

•	NEUTRAL (Manual)

Start the engine and warm to operating temperature.
Operate the A/C system for 5 minutes.
Inspect A/C components for the following conditions:

•	Abnormal frost areas

•	Unusual noises

Important: Press the RESET button, before using the print function of the J 43600 .

Print the following information:

•	The panel outlet air temperatures

•	The low-side pressure

•	The high-side pressure

Compare the low and high side pressures and the panel output temperatures to the A/C Performance Table below.

Does all the data recorded fall within the specified ranges of the A/C Performance Table below?

Go to Step 8

Go to Step 3

If the pressures and temperatures recorded do not fall within the specified ranges:

Continue to operate the A/C system for an additional 5 minutes.
RESET the J 43600 and record the pressures and temperatures again.
Compare the low and high side pressures and the panel output temperature to the table below.

Does all the data recorded fall within the specified ranges of the table below?

Go to Step 8

Go to Step 4

Do the high and low side pressures fall within the specified ranges, but the panel outlet temperatures do not?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone A

Go to Step 5

Is the low side pressure greater than the specified range, but the high side pressure within or less than the specified range?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone B

Go to Step 6

Are the low and high side pressures both greater than the specified ranges?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone C

Go to Step 7

Is the high side pressure greater than the specified range, but the low side pressure is within or less than the specified range?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone D

Go to Step 8

Operate the system in order to verify the test results.

Did you find the same results?

System OK

Go to Symptoms - HVAC Systems - Manual

A/C System Pressure-Zone Classification Graph

A/C Performance Table

Ambient Temperature	Relative Humidity	Low Side Service Port Pressure	High Side Service Port Pressure	Maximum Left Center Discharge Air Temperature
13-18°C (55-65°F)	0-100%	158-234 kPa (23-343 psi)	640-992 kPa (93-144 psi)	10°C (50°F)
19-24°C (66-75°F)	Below 40%	151-220 kPa (22-32 psi)	702-1274 kPa (102-185 psi)	10°C (50°F)
19-24°C (66-75°F)	Above 40%	172-241 kPa (25-35 psi)	792-1129 kPa (115-164 psi)	10°C (50°F)
25-29°C (76-85°F)	Below 35%	172-234 kPa (25-34 psi)	909-1446 kPa (132-210 psi)	10°C (50°F)
	35-50%	179-241 kPa (26-35 psi)	9577-1212 kPa (139-176 psi)	10°C (50°F)
	Above 50%	186-248 kPa (27-36 psi)	992-1322 kPa (144-192 psi)	12°C (52°F)
30-35°C (86-95°F)	Below 30%	186-241 kPa (27-35 psi)	1081-1371 kPa (157-199 psi)	13°C (55°F)
	30-50%	186-248 kPa (27-36 psi)	11027-1378 kPa (160-200 psi)	13°C (55°F)
	Above 50%	186-248 kPa (27-36 psi)	1129-1398 kPa (164-203 psi)	14°C (57°F)
36-41°C (96-105°F)	Below 20%	186-254 kPa (27-37 psi)	1267-1550 kPa (184-225 psi)	13°C (55°F)
	20-40%	199-261 kPa (29-38 psi)	1281-1550 kPa (186-225 psi)	14°C (57°F)
	Above 40%	220-289 kPa (32-42 psi)	1288-1715 kPa (187-249 psi)	15°C (62°F)
42-46°C (106-115°F)	Below 20%	213-268 kPa (31-39 psi)	1467-1722 kPa (213-250 psi)	15°C (59°F)
42-46°C (106-115°F)	Above 20%	213-275 kPa (31-40 psi)	1467-1818 kPa (213-264 psi)	16°C (60°F)
47-49°C (116-120°F)	Below 30%	234-303 kPa (34-44 psi)	1639-1977 kPa (238-287 psi)	19°C (65°F)

Air Conditioning (A/C) System Performance Test LE5

Table 1:

A/C Performance Table

This test measures the operating efficiency of the A/C system under the following conditions:

•	The current ambient air temperature

•	The current relative humidity

•	The high side pressure of the A/C system

•	The low side pressure of the A/C system

•	The temperature of the air being discharged into the passenger compartment

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step determines if the A/C system has at least the minimum refrigerant charge required to operate the system without damage.

This step measures the performance of the A/C system.

This step is to allow for vehicle variations as well as high ambient temperatures.

Step

Action

Values

Yes

Important:

•	The ambient air temperature must be at least 16°C (60°F) .

•	Do not induce additional air flow across the front of the vehicle during the test.

•	If you were sent here from a DTC diagnostic table, clear the DTC upon completion of this test.

Park the vehicle inside or in the shade.
Open the windows in order to ventilate the interior of the vehicle.
If the A/C system was operating, allow the A/C system to equalize for about 2 minutes.
Turn OFF the ignition.
Install the J 43600 ACR 2000 Air Conditioning Service Center.
Record the ambient air temperature displayed on the J 43600 .
Record the low and high side STATIC pressure readings.

Are both the low side and high side pressures within the specified value?

More than 16°C (60°F) - 345 kPa (50 psi)

More than 24°C (75°F) - 483 kPa (70 psi)

More than 33°C (90°F) - 690 kPa (100 psi)

Go to Step 2

Go to Leak Testing

Important: Record the relative humidity and the ambient air temperature at the time of the test.

Close the vehicle doors and windows.
Open the drivers door window 12.7-15.2 cm (5-6 in).
Select the following HVAC control settings:

•	The A/C is ON.

•	The coldest temperature setting

•	The maximum blower speed

•	Recirculation mode

•	The I/P panel outlet mode

•	All I/P panel outlets are OPEN.

Install the temperature probes of the J 43600 in the left and right center panel air outlets.
Apply the parking brake.
Place the transaxle/transmission in one of the following positions:

•	PARK (Automatic)

•	NEUTRAL (Manual)

Start the engine and warm to operating temperature.
Operate the A/C system for 5 minutes.
Inspect A/C components for the following conditions:

•	Abnormal frost areas

•	Unusual noises

Important: Press the RESET button, before using the print function of the J 43600 .

Print the following information:

•	The panel outlet air temperatures

•	The low-side pressure

•	The high-side pressure

Compare the low and high side pressures and the panel output temperatures to the A/C Performance Table below.

Does all the data recorded fall within the specified ranges of the A/C Performance Table below?

Go to Step 8

Go to Step 3

If the pressures and temperatures recorded do not fall within the specified ranges:

Continue to operate the A/C system for an additional 5 minutes.
RESET the J 43600 and record the pressures and temperatures again.
Compare the low and high side pressures and the panel output temperature to the table below.

Does all the data recorded fall within the specified ranges of the table below?

Go to Step 8

Go to Step 4

Do the high and low side pressures fall within the specified ranges, but the panel outlet temperatures do not?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone A

Go to Step 5

Is the low side pressure greater than the specified range, but the high side pressure within or less than the specified range?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone B

Go to Step 6

Are the low and high side pressures both greater than the specified ranges?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone C

Go to Step 7

Is the high side pressure greater than the specified range, but the low side pressure is within or less than the specified range?

Go to Air Conditioning (A/C) Diagnostics - Pressure Zone D

Go to Step 8

Operate the system in order to verify the test results.

Did you find the same results?

System OK

Go to Symptoms - HVAC Systems - Manual

A/C System Pressure Zone Classification Graph

A/C Performance Table

Ambient Temperature	Relative Humidity	Low Side Service Port Pressure	High Side Service Port Pressure	Maximum Left Center Discharge Air Temperature
13-18°C (55-65°F)	0-100%	151-213 kPa (22-31 psi)	730-1047 kPa (106-152 psi)	8°C (46°F)
19-24°C (66-75°F)	Below 40%	151-227 kPa (22-33 psi)	847-1178 kPa (123-171 psi)	9°C (48°F)
19-24°C (66-75°F)	Above 40%	165-248 kPa (24-36 psi)	902-1247 kPa(131-181 psi)	12°C (52°F)
25-29°C (76-85°F)	Below 35%	172-241 kPa (25-35 psi)	1061-1350 kPa (154-196 psi)	10°C (50°F)
	35-50%	179-248 kPa (26-36 psi)	1102-1371 kPa (160-199 psi)	12°C (52°F)
	Above 50%	192-261 kPa (28-38 psi)	1123-1419 kPa (163-206 psi)	13°C (55°F)
30-35°C (86-95°F)	Below 30%	192-254 kPa (28-37 psi)	1233-1543 kPa (179-224 psi)	13°C (54°F)
	30-50%	1992-268 kPa (29-39 psi)	1260-1570 kPa (183-228 psi)	13°C (55°F)
	Above 50%	206-275 kPa (30-40 psi)	1288-1619 kPa (187-235 psi)	15°C (59°F)
36-41°C (96-105°F)	Below 20%	206-275 kPa (30-40 psi)	1433-1729 kPa (208-251 psi)	13°C (55°F)
	20-40%	213-282 kPa (31-41 psi)	1446-1756 kPa (210-255 psi)	15°C (59°F)
	Above 40%	220-289 kPa (32-42 psi)	1481-1791 kPa (215-260 psi)	17°C (61°F)
42-46°C (106-115°F)	Below 20%	234-296 kPa (34-43 psi)	1632-1901 kPa (237-276 psi)	15°C (59°F)
42-46°C (106-115°F)	Above 20%	234-296 kPa (34-43 psi)	1646-1929 kPa (239-280 psi)	17°C (61°F)
47-49°C (116-120°F)	Below 30%	254-310 kPa (37-45 psi)	1818-2080 kPa (264-302 psi)	18°C (63°F)