Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P0443: Evaporative Emission (EVAP) Purge Solenoid Control CircuitDTC P0449: Evaporative Emission (EVAP) Vent Solenoid Control Circuit
Diagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
Ignition 1 Voltage - Purge Supply | P0030, P0050, P0102, P0443 | P0443 | P0443 | -- | -- |
Battery Positive - Vent Supply | P0449 | P0449 | P0449 | -- | -- |
EVAP Purge Solenoid Control | P0443 | P0443 | P0443 | P0443 | -- |
EVAP Vent Solenoid Control | P0449 | P0449 | P0449 | P0449 | -- |
Circuit/System Description
P0443
An ignition voltage is supplied directly to the evaporative emission (EVAP) canister purge solenoid valve. The EVAP canister purge solenoid valve is pulse width modulated (PWM). The scan tool displays the amount of ON time as a percentage. The control module monitors the status of the driver. The control module controls the EVAP canister purge solenoid valve ON time by grounding the control circuit via an internal switch called a driver.
P0449
Battery voltage is supplied to the EVAP canister vent solenoid valve. The control module grounds the EVAP canister vent solenoid valve control circuit to close the valve by means of an internal switch called a driver. The scan tool displays the commanded state of the EVAP canister vent solenoid valve as ON or OFF. The control module monitors the status of the driver.
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The system voltage is between 6-18 volts. |
| • | DTC P0443 and P0449 run continuously when the above conditions are met. |
Conditions for Setting the DTC
The control module detects that the commanded state of the driver and the actual state of the control circuit do not match, for a minimum of 12 seconds.
Action Taken When the DTC Sets
DTCs P0443 and P0449 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P0443 and P0449 are Type B DTCs.
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Circuit/System Verification
P0443
With the ignition ON, and the engine OFF, you should hear a clicking sound when the EVAP canister purge solenoid valve is commanded to 50 percent with a scan tool. The clicking sound should stop when the EVAP canister purge solenoid valve is commanded to 0 percent. The rate at which the valve cycles should increase when the commanded state is increased, and decrease when the commanded state is decreased.
P0449
- With the ignition ON and the engine OFF, command the EVAP vent solenoid ON and OFF with a scan tool.
- Listen for a click when the valve operates. Verify that both the ON, and the OFF states are commanded.
Circuit/System Testing
P0443
- Ignition OFF, disconnect the harness connector at the EVAP canister purge solenoid valve.
- Ignition ON, verify that a test lamp illuminates between the voltage supply circuit terminal A and ground.
- Connect a test lamp between the voltage supply circuit terminal A and the control circuit terminal B.
- Command the solenoid to 50 percent with a scan tool The test lamp should flash or illuminate when commanded to 50 percent, and turn OFF when commanded to 0 percent.
- If all circuits test normal, replace the EVAP canister purge solenoid valve.
| ⇒ | If the test lamp does not illuminate, test the voltage supply circuit for a short tog round or an open/high resistance. If the circuit tests normal and the voltage supply circuit fuse is open, test or replace the EVAP canister purge solenoid. |
| ⇒ | If the test lamp does is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the control module. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the control module. |
P0449
- Ignition OFF, disconnect the harness connector at the EVAP canister vent solenoid valve.
- Ignition ON, verify that a test lamp illuminates between the voltage supply circuit terminal A and ground.
- Connect a test lamp between the voltage supply circuit terminal A and the control circuit terminal B.
- Command the solenoid ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between commanded states.
- If all circuits test normal, replace the EVAP canister vent solenoid valve.
| ⇒ | If a test lamp does not illuminate, test the voltage supply circuit for a short to ground or an open/high resistance. If the circuit tests normal and the voltage supply circuit fuse is open, test or replace the EVAP canister vent solenoid valve. |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the control module. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the control module. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for engine control module (ECM) replacement, setup, and programming |
