Windshield Frame Header Front Panel Replacement Convertible

Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.

1. Disable the SIR system. Refer to SIR Disabling and Enabling.
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
3. Remove all related panels and components.
4. Repair as much of the damaged area as possible. Refer to Dimensions - Body.
5. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.

Note: Note the number and location of the factory welds for installation of the header panel.

6. Locate and drill out all the necessary factory welds.



7. Remove the header panel.

Note: If the location of the original plug weld holes can not be determined, space the plug weld holes every 40 mm (1½ in) apart.

1. Drill 8 mm (5/16 in) plug weld holes in the service part as necessary in the locations noted from the original panel.
2. Prepare all mating surfaces as necessary.
3. Apply GM-approved weld-thru coating or equivalent to all mating surfaces. Refer to Anti-Corrosion Treatment and Repair.



4. Position the header panel to the vehicle using 3-dimensional measuring equipment. Clamp the front header panel in place.



5. Plug weld accordingly.
6. Clean and prepare all of the welded surfaces.
7. Install all of the related panels and components.
8. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
9. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
11. Enable the SIR system. Refer to SIR Disabling and Enabling.

Windshield Frame Header Front Panel Replacement Coupe

Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.

1. Disable the SIR system. Refer to SIR Disabling and Enabling.
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
3. Remove all related panels and components.
4. Repair as much of the damaged area as possible. Refer to Dimensions - Body.
5. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.

Note: Note the number and location of the factory welds for installation of the header panel.




6. Locate and drill out all the necessary factory welds.



7. Remove the header panel.

Note: If the location of the original plug weld holes can not be determined, space the plug weld holes every 40 mm (1½ in) apart.

1. Drill 8 mm (5/16 in) plug weld holes in the service part as necessary in the locations noted from the original panel.
2. Prepare all mating surfaces as necessary.
3. Apply GM-approved weld-thru coating or equivalent to all mating surfaces. Refer to Anti-Corrosion Treatment and Repair.



4. Position the header panel to the vehicle using 3-dimensional measuring equipment. Clamp the front header panel in place.



5. Plug weld accordingly.
6. Clean and prepare all of the welded surfaces.
7. Install all of the related panels and components.
8. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
9. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
11. Enable the SIR system. Refer to SIR Disabling and Enabling.

Windshield Frame Header Front Panel Replacement Sedan

Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.

1. Disable the SIR system. Refer to SIR Disabling and Enabling.
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
3. Remove all related panels and components.
4. Repair as much of the damaged area as possible. Refer to Dimensions - Body.
5. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.

Note: Note the number and location of the factory welds for installation of the header panel.




6. Locate and drill out all the necessary factory welds.



7. Remove the header panel.

Note: If the location of the original plug weld holes can not be determined, space the plug weld holes every 40 mm (1½ in) apart.

1. Drill 8 mm (5/16 in) plug weld holes in the service part as necessary in the locations noted from the original panel.
2. Prepare all mating surfaces as necessary.
3. Apply GM-approved weld-thru coating or equivalent to all mating surfaces. Refer to Anti-Corrosion Treatment and Repair.



4. Position the header panel to the vehicle using 3-dimensional measuring equipment. Clamp the front header panel in place.



5. Plug weld accordingly.
6. Clean and prepare all of the welded surfaces.
7. Install all of the related panels and components.
8. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
9. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
11. Enable the SIR system. Refer to SIR Disabling and Enabling.