Diagnostic Instructions
DTC Descriptors
DTC P2728: Clutch Pressure Control (PC) Solenoid 5 System Performance
DTC P2729: Clutch Pressure Control (PC) Solenoid 5 Control Circuit Low Voltage
DTC P2730: Clutch Pressure Control (PC) Solenoid 5 Control Circuit High Voltage
Circuit/System Description
The clutch pressure control (PC) solenoid 5 is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The TCM supplies 12 volts to the clutch PC solenoid 5 through the high side driver 2
circuit. The TCM control the clutch PC solenoid 5 through the clutch PC solenoid 5 control circuit. The normally low clutch PC solenoid 5 flows fluid to the 1-2-3-4 clutch when commanded ON and exhausts fluid when commanded OFF. The clutch
PC solenoid 5 regulates the transmission fluid pressure to the 1-2-3-4 clutch.
Conditions for Running the DTC
P2728
| • | DTC P2728 has not failed this ignition cycle. |
| • | The engine run time is greater than 5 seconds. |
| • | The ignition voltage is between 8.6-19.0 volts. |
P2729
| • | DTC P2729 has not failed this ignition cycle. |
| • | The engine run time is greater than 5 seconds. |
| • | The ignition voltage is between 8.6-19.0 volts. |
P2730
| • | DTC P2730 has not failed this ignition cycle. |
| • | The engine run time is greater than 5 seconds. |
| • | The ignition voltage is between 8.6-19.0 volts. |
Conditions for Setting the DTC
P2728
The TCM detects an invalid voltage in the clutch PC solenoid 5 control circuit for 4.4 seconds or greater in a 5.0 second sample.
P2729
The TCM detects low voltage on the clutch PC solenoid 5 control circuit for 300 milliseconds or greater in a 375 millisecond sample.
P2730
The TCM detects high voltage on the clutch PC solenoid 5 control circuit for 300 milliseconds or greater in a 375 millisecond sample.
Action Taken When the DTC Sets
P2728
| • | DTC P2728 is a Type C DTC. |
| • | The TCM freezes transmission adaptive functions. |
P2729 and P2730
| • | DTCs P2729 and P2730 are Type A DTCs. |
| • | The TCM forces High Side Drive 1 and 2 OFF. |
| • | The TCM inhibits the TCC. |
| • | The TCM commands maximum line pressure. |
| • | The TCM freezes transmission adaptive functions. |
Conditions for Clearing the DTC
| • | DTC P2728 is a Type C DTC. |
| • | DTCs P2729 and P2730 are Type A DTCs. |
Reference Information
Description and Operation
Transmission General Description
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit Verification
- Ensure the transmission fluid temperature is between 50-80°C (122-176°F).
- Perform the
Control Solenoid Valve and Transmission Control Module Assembly Cleaning to dislodge debris and free up the valves.
- Operate the vehicle in 2nd gear long enough to ensure at least a 3°C (5°F) rise in TCM temperature.
- Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
| ⇒ | If the DTC does not reset, replace the control solenoid (w/body and TCM) valve assembly. |
Repair Instructions
Important:
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
