A structural diecast aluminium oil pan incorporates an oil suction pipe, a baffle, a windage tray, and an oil level sensor. The oil suction pipe is bolted into the oil pan and seals to the bottom of the block with O-ring gasket. The baffle is mounted to the lower portion of the 6.5 litre (6.9 quart) capacity oil pan sump and ensures oil supply to the oil suction pickup. The windage tray is bolted to the upper portion of the oil pan and reduces friction losses at high speed. The oil level sensor is mounted through the bottom of the oil pan.

A crankshaft driven gerotor oil pump with internal pressure-relief valve is mounted to the front of the cylinder block and pulls oil from the oil suction pipe through the lower passage in the cylinder block. The oil pump then directs the flow of pressurized oil back through the upper passage in the block to the left side of the cylinder block where the oil filter adapter is mounted.

An oil filter adapter is mounted with a gasket to the left side of the cylinder block. The oil filter adapter incorporates a top-access, cartridge style oil filter. The filter is accessed through a screw on cap with an O-ring gasket. The oil filter adapter cap has a built-in oil bypass valve. The oil filter adapter housing incorporates a drain back control valve and a threaded oil pressure sending unit. Oil flows through the lower passage in the oil filter adapter up to and through the oil filter cartridge. Filtered oil travels back through the upper passage of the oil filter adapter and back into the cylinder block.

Oil is directed up and across the cylinder block front through several drilled passages. These front passages feed oil to each cylinder head, oil to the passage for the main bearings and piston oil jets, oil to the right and left secondary idler sprockets, and oil to the primary timing drive chain tensioner.

Each cylinder head passage directs oil into the cylinder head where it is directed to oiling circuits for the Stationary Hydraulic Lifter assemblies (SHLAs) and the camshaft bearing journals. Oil is also directed through 2 passages each with a spring-loaded check-ball valve to the 2 chambers where the camshaft position actuator oil control solenoid valves are mounted. Each chamber contains a camshaft position actuator oil control solenoid valve with built-in oil filter screen. One camshaft position actuator oil control solenoid valve is used to control the exhaust camshaft position actuator and 1 camshaft position actuator oil control solenoid valve is used to control the intake camshaft position actuator. The Engine Control Module (ECM) electrically controls each camshaft position actuator oil control solenoid valve. When energized by the ECM the camshaft position actuator oil control solenoid valve directs oil to pass up through the cylinder head front camshaft bearing cap. Oil passes through the camshaft bearing cap passage into oil holes drilled into the side of the front camshaft journal and onto the front of the camshaft mounting surface. Oil passes through to matching passages in the camshaft position actuator. Oil is directed by the camshaft position actuator oil control solenoid valve to the appropriate passage in the system to pressurize oil on the vanes on the inside of the of the camshaft position actuator. Oil acting on the vanes rotates the camshaft mounted to the inner camshaft position actuator rotor relative to the sprocket mounted to the outer camshaft position actuator housing. An internal lock pin locks the inner rotor to the outer camshaft position actuator housing at idle and maintains the camshaft position actuator in the home or default position during start-up conditions. Oil pressure directed by the camshaft position actuator oil control solenoid valve unlocks the pin and allows the camshaft position actuator to function. An additional passage in the cylinder head also directs oil to the secondary timing drive chain tensioner mounted to each cylinder head.

The oil passage that supplies oil to the main bearings also supplies oil to pressure-actuated piston-cooling oil jets. Each oil jet is mounted between opposing cylinder bores and directs oil to the 2 bores to provide extra cooling and control piston temperatures.

Oil is directed from the front passages to the front of the block where the right and left secondary idler sprockets and the primary timing drive chain tensioner are mounted. Each camshaft timing drive chain tensioner relies on a gasket in order to maintain an oil reserve after the engine is turned OFF. All camshaft timing drive chain tensioners incorporate a small oil jet to supply an oil spray onto the camshaft timing drive chain components.

Oil returns to the oil pan sump either through the camshaft timing drive chain area or through the cast oil drain back passages on the outboard walls of the cylinder heads and cylinder block.