Circuit Description
The control module enables the appropriate fuel injector on the intake stroke for each cylinder. Ignition 1 voltage is supplied to the fuel injectors. The control module controls each fuel injector by grounding the control circuit via a solid state device called a driver. The control module monitors the status of each driver. If the control module detects an incorrect voltage for the commanded state of the driver, a fuel injector control DTC sets.
DTC Descriptors
This diagnostic procedure supports the following DTC.
DTC P0200 Injector Control Circuit
Conditions for Running the DTC
| • | The engine speed is more than 400 RPM. |
| • | The ignition voltage is between 10-18 volts. |
Conditions for Setting the DTC
| • | The powertrain control module (PCM) detects an incorrect voltage on a fuel injector control circuit. |
| • | The condition exists for 5 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Performing the Fuel Injector Coil Test may help to isolate an intermittent condition. Refer to Fuel Injector Solenoid Coil Test . |
| • | For an intermittent condition, refer to Intermittent Conditions . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies that the PCM is able to control the fuel injector.
-
This step tests if a ground is constantly being applied to the fuel injector.
Step | Action | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views | |||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | Go to Step 2 | |||||||
2 |
Are any of the misfire current counters incrementing? | Go to Step 4 | Go to Step 3 | ||||||
3 |
Did the DTC fail this ignition? | Go to Step 4 | Go to Diagnostic Aids | ||||||
4 |
Does the test lamp illuminate? | Go to Step 5 | Go to Step 11 | ||||||
Does the test lamp flash? | Go to Step 9 | Go to Step 6 | |||||||
Does the test lamp remain illuminated? | Go to Step 8 | Go to Step 7 | |||||||
7 | Test the fuel injector control circuit for the following conditions:
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 10 | ||||||
8 | Test the fuel injector control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 13 | ||||||
9 | Test for an intermittent and for a poor connection at the fuel injector. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 12 | ||||||
10 | Test for an intermittent and for a poor connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 13 | ||||||
11 |
Important: The INJ fuse also supplies voltage to the ignition coil modules. If the fuse is open, inspect all related circuits and components for a short to ground. Refer to Circuit Testing in Wiring Systems. Test the ignition 1 voltage circuit of the fuel injector for:
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | -- | ||||||
12 | Replace the fuel injector. Refer to Fuel Injector Replacement . Did you complete the replacement? | Go to Step 14 | -- | ||||||
13 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | Go to Step 14 | -- | ||||||
14 |
Did the DTC fail this ignition? | Go to Step 2 | Go to Step 15 | ||||||
15 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | System OK | |||||||
