GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2006 🢒 GTO 🢒 DTC 🢒 DTC 0069 or 0070

Circuit Description

The seat belt pretensioner deployment loop consists of a seat belt pretensioner, the seat belt pretensioner high and seat belt pretensioner low circuits. A shorting bar is used in the seat belt pretensioner connector, which will short together the seat belt pretensioner high and seat belt pretensioner low circuits, when the connector is disconnected. This will help to prevent unwanted deployment of the seat belt pretensioner during servicing. During a frontal crash of sufficient force, the sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the seat belt pretensioner. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity, and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored.

DTC Descriptor

This diagnostic procedure supports the following DTCs:

DTC 0069 RF Pretensioner Deployment Loop Resistance High

DTC 0070 RF Pretensioner Deployment Loop Resistance Low

Conditions for Running the DTC

Ignition voltage is within the normal operating voltage range.

Conditions for Setting the DTC
    • DTC 0069 will set when the SDM detects a high resistance condition in the RH seat belt pretensioner deployment loop.
    • DTC 0070 will set when the SDM detects a low resistance condition in the RH seat belt pretensioner deployment loop.

Action Taken When the DTC Sets

The SDM commands the AIR BAG indicator ON.

Conditions for Clearing the DTC

The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.

Diagnostic Aids

Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction.

The following are possible causes of the malfunction:

    • An open or high resistance in the seat belt pretensioner high or the seat belt pretensioner low circuits
    • A short between the seat belt pretensioner high and the seat belt pretensioner low circuits
    • A malfunctioning RH seat belt pretensioner
    • An internal SDM malfunction

If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests to see if the malfunction is caused by the seat belt pretensioner.

    2.

  2. If DTC 0069 is present, test the seat belt pretensioner high and the seat belt pretensioner low circuits for an open or high resistance.

    If DTC 0070 is present, test for a short between the seat belt pretensioner high and the seat belt pretensioner low circuits.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

Connector End View Reference: SIR Connector End Views

1

Did you perform a Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Is DTC 0069 or 0070 set as a current DTC?

Go to Step 3

Go to Diagnostic Aids

3
  1. Turn OFF the ignition.
  2. Disconnect the RH seat belt pretensioner connector.
  3. Inspect both the component and harness sides of the RH seat belt pretensioner connectors for damage or corrosion that may cause the malfunction. Refer to Testing for Intermittent Conditions and Poor Connections .

Does the connector exhibit any signs of damage or corrosion?

Go to Step 4

Go to Step 5

4
    • If the component side of the seat belt pretensioner connector is damaged, the seat belt pretensioner must be replaced. Refer to Seat Belt Buckle Pretensioner Replacement .
    • If the harness side of the RH seat belt pretensioner connector is damaged, replace the harness side of the connector. Refer to Connector Repairs .

Did you complete the replacement?

Go to Step 10

--

5

  1. Install EL-46841 SIR Pretensioner Load Tool to the seat belt pretensioner harness connector.
  2. Connect the battery. Refer to Battery Negative Cable Disconnection and Connection .
  3. Use the scan tool in order to clear the DTCs.
  4. With the scan tool, request the DTC display.

Does the scan tool indicate that DTC 0069 or 0070 is current?

Go to Step 6

Go to Step 8

6
  1. Turn OFF the ignition.
  2. Disconnect the sensing and diagnostic module (SDM) connector.
  3. Inspect the SDM connector for damage or corrosion that may cause a malfunction between the seat belt pretensioner high and/or the seat belt pretensioner low circuits. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 7

7

    • If DTC 0069 is present, test the seat belt pretensioner high and the seat belt pretensioner low circuits for an open or high resistance.
    • If DTC 0070 is present, test for a short between the seat belt pretensioner high and the seat belt pretensioner low circuits.
    • For all the above conditions, refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 9

8
  1. Turn OFF the ignition.
  2. Replace the RH seat belt pretensioner. Refer to Seat Belt Buckle Pretensioner Replacement .

Did you complete the replacement?

Go to Step 10

--

9

Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .

Did you complete the replacement?

Go to Step 10

--

10
  1. Reconnect all SIR components.
  2. Verify that all components, connectors and connector position assurances (CPAs) are properly mounted.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK