GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2000 🢒 Grand Prix 🢒 Restraints 🢒 SIR 🢒 DTC B0017 RF/Passenger Frontal Deployment Loop (Single Stage or Stage 1) Open

Object Number: 590448 Size: SF
SIR Component Views
Power/Grounds, Inflator Modules
SIR Handling Caution

Circuit Description

When you first turn ON the ignition, the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:

    • Deployment loop voltage out of range test
    • Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be performed.

Conditions for Running the DTC

Deployment loop voltage out of range test:

    • Ignition 1 voltage is within the normal operating voltage range.
    • Passenger frontal deployment loop is not shorted to voltage.
    • Passenger frontal high circuit is less than 2 volts.

Deployment loop resistance measurement test:

    • Ignition 1 voltage is within the normal operating voltage range.
    • Passenger frontal deployment loop is not shorted to voltage.
    • Passenger frontal deployment loop is not shorted to ground.

Conditions for Setting the DTC

Deployment loop voltage out of range test - Passenger frontal deployment loop resistance is at least 6 ohms for 300 milliseconds.

Deployment loop resistance measurement test - Passenger frontal deployment loop resistance is more than 3.7 ohms for 300 milliseconds.

Action Taken When the DTC Sets

The SDM commands ON the AIR BAG warning lamp.

Conditions for Clearing the DTC
    • You can issue a CLEAR CODES command
    • A history DTC will clear once 255 malfunction free ignition cycles have occurred

Diagnostic Aids

The following can cause an intermittent condition:

    • The inflatable restraint IP module yellow 2-way connector.
    • The SDM wiring harness connector.
    • The wire to terminal connections in the passenger frontal high circuit.
    • The wire to terminal connections in the passenger frontal low circuit.
    • Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

  1. This step checks the inline connector C216.

    2.

  2. This step isolates the malfunction to one side of inline connector C216.

    3.

  3. This step checks to see if the SDM wiring harness connector is OK.

    4.

  4. This step checks to see if there is an open or a high resistance in the passenger frontal high circuit between inline connector C216 and the SDM wiring harness connector.

    5.

  5. This step determines if there is an open or high resistance in the passenger frontal low circuit between inline connector C216 and the SDM wiring harness connector or if there is a malfunctioning SDM.

DTC B0017 Passenger Frontal Deployment Loop Open

Step

Action

Value(s)

Yes

No

1

Did you perform the SIR Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - SIR

2

  1. Turn OFF the ignition.
  2. Disconnect the inline connector C216.
  3. Inspect the male and female sides of inline connector C216 for the following conditions. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    4. • Corrosion
    • Damaged terminals
    • Poor connections/terminal tension

Does either the male or female side of inline connector C216 exhibit any signs of corrosion, terminal damage, or poor connections?

--

Go to Step 3

Go to Step 4

3
  1. If the female side of the inline connector is damaged, the wiring harness must be replaced.
  2. If the male side of the inline connector is damaged, replace the male side of the inline connector. Refer to Connector Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 14

--

4
  1. Reconnect the inline connector C216.
  2. Verify that the connector position assurance (CPA) is properly installed.
  3. Turn ON the ignition, with the engine OFF.
  4. Use the scan tool to request the SIR DTC display.

Does the scan tool indicate that this DTC is current?

--

Go to Step 5

Go to Diagnostic Aids

5

  1. Turn OFF the ignition.
  2. Disconnect the inline connectors C215 and C216.
  3. Install the J 38715-A SIR Driver/Passenger Load Tool to the wiring harness side of inline connectors C215 and C216. Use the J 38715-5 adaptor for inline connector C216 and the J 38715-90 adaptor for inline connector C215.
  4. Turn ON the ignition, with the engine OFF.
  5. Use the scan tool to request the SIR DTC display.

Does the scan tool indicate that this DTC is current?

--

Go to Step 7

Go to Step 6

6
  1. Turn OFF the ignition.
  2. Replace the inflatable restraint IP module. Refer to Inflatable Restraint Instrument Panel Module Replacement .

Did you complete the replacement?

--

Go to Step 14

--

7

  1. Turn OFF the ignition.
  2. Remove the J 38715-A .
  3. Disconnect the inflatable restraint sensing and diagnostic module (SDM). Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  4. Inspect the SDM wiring harness connector for the following conditions. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    5. • Corrosion
    • Damaged terminals
    • Poor connections/terminal tension

Does the SDM wiring harness connector exhibit any signs of corrosion, terminal damage, or poor connections?

--

Go to Step 8

Go to Step 9

8

Replace the SDM wiring harness connector. Refer to Connector Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 14

--

9

  1. Zero the J 39200 Digital Multimeter (DMM).
  2. Use the DMM to measure the resistance of the passenger frontal high circuit between the inline connector C216 and the SDM wiring harness connector.

Does the resistance measure less than the specified value?

0.5 ohms

Go to Step 11

Go to Step 10

10

Locate and repair the open or high resistance in the passenger frontal high circuit between the inline connector C216 and the SDM wiring harness connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 14

--

11

Use the J 39200 to measure the resistance of the passenger frontal low circuit between the inline connector C216 and the SDM wiring harness connector.

Does the resistance measure less than the specified value?

0.5 ohms

Go to Step 13

Go to Step 12

12

Locate and repair the open or high resistance in the passenger frontal low circuit between the inline connector C216 and the SDM wiring harness connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 14

--

13

Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .

Did you complete the replacement?

--

Go to Step 14

--

14
  1. Reconnect all SIR components.
  2. Verify that all components and connectors are properly mounted.
  3. Turn ON the ignition, with the engine OFF.
  4. Use the scan tool in order to clear the DTCs.

Did you complete the action?

--

Go to Diagnostic System Check - SIR

--