GM Service Manual Online
For 1990-2009 cars only

Drive Belt Tensioner Replacement L36/L67

Removal Procedure


    Object Number: 326960  Size: SH

    Caution: Before servicing any electrical component, the ignition and start switch must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Drain the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  3. Remove the coolant recovery reservoir. Refer to Coolant Recovery Reservoir Replacement in Engine Cooling.
  4. Remove the drive belt. Refer to Drive Belt Replacement .
  5. Remove the generator. Refer to Generator Replacement in Engine Electrical.
  6. Remove the heater hose adapters with the heater hoses from the drive belt tensioner. Refer to Heater Hoses Replacement in Heating Ventilation and Air Conditioning.
  7. Remove the accessory drive belt tensioner bolts.
  8. Remove the accessory drive belt tensioner.
  9. If replacing the drive belt tensioner, remove the thermostat bypass upper and lower pipe assemblies.

Installation Procedure


    Object Number: 326960  Size: SH
  1. If replacing the accessory drive belt tensioner, lubricate the seals with engine coolant and install the thermostat bypass upper and lower pipe assemblies.
  2. Install the accessory drive belt tensioner.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the accessory drive belt tensioner bolts.
  5. Tighten
    Tighten the accessory drive belt tensioner bolts to 50 N·m (37 lb ft).

  6. Install the heater hose adapters with the heater hoses to the drive belt tensioner. Refer to Heater Hoses Replacement in Heating Ventilation and Air Conditioning.
  7. Install the generator. Refer to Generator Replacement in Engine Electrical.
  8. Install the drive belt. Refer to Drive Belt Replacement .
  9. Install the coolant recovery reservoir. Refer to Coolant Recovery Reservoir Replacement in Engine Cooling.
  10. Fill the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  11. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

Drive Belt Tensioner Replacement Supercharger

Removal Procedure


    Object Number: 190587  Size: SH
  1. Remove the supercharger drive belt. Refer to Drive Belt Replacement .

  2. Object Number: 97873  Size: SH
  3. Remove the drive belt tensioner nut.
  4. Remove the drive belt tensioner.

Installation Procedure


    Object Number: 97873  Size: SH
  1. Install the drive belt tensioner.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the drive belt tensioner nut.
  4. Tighten
    Tighten the drive belt tensioner nut to 50 N·m (37 lb ft).


    Object Number: 190587  Size: SH
  5. Install the supercharger drive belt. Refer to Drive Belt Replacement .