Exhaust Manifold Replacement - Right Side 3.1L

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
2. Remove the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement in Engine Controls - 3.1L.
3. Remove the accelerator and cruise control cables with the bracket from the throttle body. Refer to Accelerator Control Cable Bracket Replacement in Engine Controls - 3.1L.
4. Rotate the engine for service access. Refer to Rotating the Engine for Service Access in Engine Mechanical - 3.1L.
5. Remove the manifold absolute pressure (MAP) sensor. Refer to Manifold Absolute Pressure Sensor Replacement in Engine Controls - 3.1L.
6. Remove the ignition control module and the ignition control module bracket. Refer to Ignition Control Module Replacement in Engine Controls - 3.1L.



7. Disconnect the heated oxygen (HO2S) sensor electrical connector.
8. Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Engine Cooling.



9. Remove the exhaust crossover pipe heat shield bolts.
10. Remove the exhaust crossover pipe heat shield.



11. Remove the exhaust crossover pipe nuts from the right exhaust manifold.
12. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
13. Remove the catalytic converter. Refer to Catalytic Converter Replacement .
14. Remove the exhaust gas recirculation (EGR) pipe from the right exhaust manifold. Refer to Exhaust Gas Recirculation Pipe Replacement in Engine Controls - 3.1L.



15. Remove the right exhaust manifold upper heat shield bolts.
16. Remove the right exhaust manifold upper heat shield.



17. Remove the right exhaust manifold lower heat shield bolts.
18. Remove the right exhaust manifold lower heat shield.



19. Remove the right exhaust manifold nuts.
20. Remove the right exhaust manifold.
21. Remove the right exhaust manifold gasket.
22. Clean and inspect the right exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection in Engine Mechanical - 3.1L.



23. If replacing the right exhaust manifold remove the heated oxygen (HO2S) sensor. Refer to Heated Oxygen Sensor 1 Replacement in Engine Controls - 3.1L.

1. If replacing the right exhaust manifold install the heated oxygen (HO2S) sensor. Refer to Heated Oxygen Sensor 1 Replacement in Engine Controls - 3.1L.



2. Install the right exhaust manifold gasket.
3. Install the right exhaust manifold.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the right exhaust manifold nuts.

Tighten
Tighten the nuts to 16 N·m (12 lb ft).




5. Install the right exhaust manifold lower heat shield.
6. Install the right exhaust manifold lower heat shield bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).




7. Install the right exhaust manifold upper heat shield.
8. Install the right exhaust manifold upper heat shield bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).

9. Install the EGR pipe to the right exhaust manifold. Refer to Exhaust Gas Recirculation Pipe Replacement in Engine Controls - 3.1L.
10. Install the catalytic converter. Refer to Catalytic Converter Replacement .
11. Lower the vehicle.



12. Install the exhaust crossover pipe nuts to the right exhaust manifold.

Tighten
Tighten the nuts to 25 N·m (18 lb ft).




13. Install the exhaust crossover pipe heat shield.
14. Install the exhaust crossover pipe heat shield bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).

15. Install the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Engine Cooling.



16. Connect the heated oxygen (HO2S) sensor electrical connector.
17. Install the ignition control module and the ignition control module bracket. Refer to Ignition Control Module Replacement in Engine Controls - 3.1L.
18. Install the MAP sensor. Refer to Manifold Absolute Pressure Sensor Replacement in Engine Controls - 3.1L.
19. Return the engine to the original position.
20. Install the engine mount struts. Refer to Engine Mount Strut Replacement in Engine Mechanical - 3.1L.
21. Install the accelerator and cruise control cables with the bracket to the throttle body. Refer to Accelerator Control Cable Bracket Replacement in Engine Controls - 3.1L.
22. Install the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement in Engine Controls - 3.1L.
23. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

Exhaust Manifold Replacement - Right Side 3.8L

1. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement in Engine Mechanical - 3.8L.
2. Remove the exhaust crossover heat shield nuts.
3. Remove the exhaust crossover heat shield.



4. Remove the exhaust crossover pipe bolts from the right exhaust manifold.
5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



6. Remove the exhaust manifold pipe stud nuts and the catalytic converter pipe from the right exhaust manifold.



7. Remove the exhaust gas recirculation (EGR) valve inlet adapter pipe bolt from the right exhaust manifold.
8. Lower the vehicle.
9. Rotate the engine to access the right side of the engine. Refer to Rotating the Engine for Service Access in Engine Mechanical - 3.8L.



10. Disconnect the heated oxygen (HO2S) sensor electrical connector (4).
11. Remove the heated oxygen (HO2S) sensor electrical connector (4) from the engine sight shield bracket (1).
12. Remove the right side spark plugs from cylinders 2, 4 and 6. Refer to Spark Plug Replacement in Engine Controls - 3.8L.



13. Remove the right engine lift bracket bolt and the nut.
14. Remove the right engine lift bracket.



15. Remove the fuel injector sight shield bracket nuts.
16. Remove the fuel injector sight shield bracket.



17. Remove the right exhaust manifold bolts and the nuts.
18. Remove the right exhaust manifold.
19. Remove the right exhaust manifold gasket.



20. Remove the upper right exhaust manifold heat shield.



21. Remove the lower right exhaust manifold heat shield.
22. If replacing the right exhaust manifold remove the heated oxygen (HO2S) sensor from the right exhaust manifold. Refer to Heated Oxygen Sensor 1 Replacement in Engine Controls - 3.8L.



23. Remove the exhaust manifold studs if damaged.
24. Clean and Inspect the right exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection in Engine Mechanical - 3.8L.

1. Install the exhaust manifold studs if removed.
2. If replacing the right exhaust manifold, install the heated oxygen (HO2S) sensor to the right exhaust manifold. Refer to Heated Oxygen Sensor 1 Replacement in Engine Controls - 3.8L.



3. Install the lower right exhaust manifold heat shield.



4. Install the upper right exhaust manifold heat shield.



5. Install the new right exhaust manifold gasket.
6. Install the right exhaust manifold.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Install the right exhaust manifold bolts and the nuts.

Tighten
Tighten the bolts and the nuts to 30 N·m (22 lb ft).




8. Install the fuel injector sight shield bracket.
9. Install the fuel injector sight shield bracket nuts.

Tighten
Tighten the nuts to 30 N·m (22 lb ft).




10. Install the right engine lift bracket.
11. Install the right engine lift bracket bolt and the nut.

Tighten
Tighten the bolt and the nut to 30 N·m (22 lb ft).

12. Install the right side spark plugs to cylinders 2, 4 and 6. Refer to Spark Plug Replacement in Engine Controls - 3.8L.



13. Install the heated oxygen (HO2S) sensor electrical connector (4) to the engine sight shield bracket (1).
14. Connect the heated oxygen (HO2S) sensor electrical connector (4).
15. Return the engine to the original position.
16. Raise the vehicle.



17. Install the EGR valve inlet adapter pipe to the right exhaust manifold.

Tighten
Tighten the bolt to 29 N·m (21 lb ft).




18. Install the catalytic converter pipe to the right exhaust manifold.
19. Install the catalytic converter pipe stud nuts to the right exhaust manifold.

Tighten
Tighten the stud nuts to 32 N·m (24 lb ft).

20. Lower the vehicle.



21. Install the exhaust crossover bolts to the right exhaust manifold.

Tighten
Tighten the bolts to 20 N·m (15 lb ft).




22. Install the exhaust crossover heat shield.
23. Install the exhaust crossover heat shield nuts.

Tighten
Tighten the nuts to 20 N·m (15 lb ft).

24. Install the engine mount struts. Refer to Engine Mount Strut Replacement - Right Side and Engine Mount Strut Replacement - Left Side in Engine Mechanical - 3.8L.
25. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement in Engine Mechanical - 3.8L.