Circuit Description
The pump motor is an integral part of the BPMV, while the pump motor relay is integral to the EBCM. The pump motor relay is not engaged during normal system operation. When ABS or TCS operation is required the EBCM activates the pump motor relay and battery power is provided to the pump motor.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC C0110 Pump Motor Circuit Malfunction
Conditions for Running the DTC
| • | The ignition switch is in the ON position. |
| • | Initialization is complete. |
Conditions for Setting the DTC
| • | Pump motor voltage is not present 60 milliseconds after activation of the pump motor relay. |
| • | Pump motor voltage is present for more than 2.5 seconds with no activation of the pump motor relay. |
| • | Pump motor voltage is not present for 40 milliseconds after the pump motor relay is commanded off. |
Action Taken When the DTC Sets
If equipped, the following actions occur:
| • | The EBCM disables the ABS/TCS/VSES for the duration of the ignition cycle. |
| • | A malfunction DTC will set. |
| • | The ABS indicator turns ON. |
| • | The Stability Off indicator turns ON. |
| • | The Red BRAKE Warning indicator could turn on. |
Conditions for Clearing the DTC
| • | The condition for the DTC is no longer present and the DTC is cleared with a scan tool. |
| • | The electronic brake control module (EBCM) automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles. |
Diagnostic Aids
| • | It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction. |
| • | Thoroughly inspect any circuitry that may be causing the complaint for the following conditions: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Improperly formed or damaged terminals |
| - | Poor terminal-to-wiring connections |
| - | Physical damage to the wiring harness |
| • | The following conditions may cause an intermittent malfunction: |
| - | A poor connection |
| - | Rubbed-through wire insulation |
| - | A broken wire inside the insulation |
| • | If an intermittent malfunction exists refer to Testing for Intermittent Conditions and Poor Connections . |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Antilock Brake System Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Did you find and correct the condition? | -- | Go to Step 8 | Go to Step 3 |
Does the resistance measure less than the specified value? | 5 ohms | Go to Step 4 | Go to Step 5 | |
4 | Inspect for poor connections at the pump motor harness pigtail connector of the BPMV. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 8 | Go to Step 6 |
5 | Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 8 | Go to Step 7 |
6 | Replace the BPMV. Refer to Brake Pressure Modulator Valve Replacement . Did you complete the repair? | -- | Go to Step 8 | -- |
7 | Replace the EBCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the repair? | -- | Go to Step 8 | -- |
8 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
