GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0521: Engine Oil Pressure (EOP) Sensor Performance

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Engine Oil Pressure 5-Volt Reference Circuit

P0522

P0522

--

P0521

Engine Oil Pressure Sensor Signal Circuit

P0522

P0522

P0523

P0521

Low Reference

--

P0523

--

P0521

Circuit/System Description

The engine oil pressure (EOP) sensor changes voltage based on the engine oil pressure. The EOP sensor is a 3-wire sensor comprising of the signal circuit, the low reference circuit and the 5-volt reference circuit. The engine control module (ECM) supplies 5-volts to the EOP sensor via the 5-volt reference circuit and provides ground via the EOP low reference circuit. The ECM monitors the signal circuit of the EOP sensor to determine if the engine oil pressure sensor voltage is within the normal operating range of approximately 1-4 volts. When the engine oil pressure is high, the EOP sensor voltage is high and the ECM senses a high signal voltage. When the engine oil pressure is low, the EOP sensor voltage is low and the ECM senses a low signal voltage. The ECM sends the EOP information to the instrument panel cluster (IPC) via the serial data circuit.

Conditions for Running the DTC

    • The engine is running with engine speed between 700-3,500 RPM.
    • Oil temperature is less than 150°C (302°F).
    • Engine load stability is less than 250 kPa (36.2 psi).
    • Engine predicted pressure is between 50 kPa (7.3 psi) and 400 kPa (58 psi).
    • No crank sensor DTCs set.
    • No coolant sensor DTCs set.
    • No intake air temperature sensor DTCs set.
    • No MAF DTCs set.
    • No oil pressure sensor circuit DTCs set.

Conditions for Setting the DTC

The ECM detects that the difference between the predicted oil pressure and the actual oil pressure is either less than 47 kPa (6.8 psi) or greater than 50 kPa (7.3 psi).

Action Taken When the DTC Sets

    • The ECM records the operating conditions at the time the diagnostics test fails. The ECM displays this information in the Failure Records on the scan tool.
    • The IPC illuminates the EOP indicator.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction-free warm-up cycles.

Reference Information

Schematic Reference

    •  Instrument Cluster Schematics
    •  Engine Controls Schematics

Connector End View Reference

    •  Displays and Gages Connector End Views
    •  Engine Control Module Connector End Views
    •  Inline Harness Connector End Views

Description and Operation

Instrument Cluster Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Scan Tool Data List

Circuit/System Verification

Engine ON, observe the Engine Oil Pressure Sensor parameter. The reading should be between 41-448 kPa (6-65 psi).

Circuit/System Testing

  1. Engine ON, transmission in park, vary the engine speed by 500 RPM.
  2. Verify the scan tool Engine Oil Pressure Sensor parameter changes by more than 34.5 kPa (5 psi).
  3. If less than 34.5 kPa (5 psi), refer to .
  4. If the pressure tests normal, replace the EOP sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Engine Oil Pressure Sensor and/or Switch Replacement
    •  Control Module References for the ECM replacement, setup and programming