GM Service Manual Online
For 1990-2009 cars only

Intake Manifold Replacement Upper

Removal Procedure

Important: The fuel injector wiring harness connectors must be connected to their respective fuel injectors. Failure to connect the fuel injector connectors to their respective fuel injectors may result in excessive exhaust emissions and poor engine performance.

  1. Drain the engine coolant from the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  2. Remove the throttle body air inlet duct. Refer to Air Filter Element Replacement in Engine Controls - 3.4L.
  3. Remove the accelerator control and cruise control cables with bracket from the throttle body. Refer to Accelerator Control Cable Replacement in Engine Controls - 3.4L.
  4. Disconnect the wiring harness connectors from the following throttle body components:
  5. • Throttle Position (TP) sensor
    • Idle Air Control (IAC) valve
  6. Disconnect the engine left side spark plug wires. Refer to Spark Plug Wire Harness Replacement in Engine Electrical.
  7. Disconnect the engine left side spark plug wire harness attachment clip. Refer to Spark Plug Wire Harness Replacement in Engine Electrical.
  8. Disconnect the throttle body heater hoses. Refer to Throttle Body Heater Inlet Hose Replacement and Throttle Body Heater Outlet Hose Replacement in Engine Cooling.

  9. Object Number: 261279  Size: SH
  10. Disconnect the vacuum hoses from the evaporative emission (EVAP) canister purge solenoid valve.
  11. Remove the EVAP canister purge solenoid valve. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement in Engine Controls - 3.4L.

  12. Object Number: 261282  Size: SH
  13. Remove the ignition coil bracket.

  14. Object Number: 190605  Size: SH
  15. Disconnect the wiring harness from the manifold air pressure (MAP) sensor.

  16. Object Number: 248103  Size: SH
  17. Disconnect the vacuum harness from the MAP sensor and the upper intake manifold.

  18. Object Number: 261271  Size: SH
  19. Disconnect and remove the emission control vacuum harness.
  20. Disconnect the vacuum brake booster hose from the upper intake manifold. Refer to Vacuum Brake Booster Hose Replacement in Hydralic Brakes.
  21. Disconnect the vacuum hose connections from the upper intake manifold.
  22. • heating, ventilation and air conditioning (HVAC) vacuum source hose
    • Fuel pressure regulator
  23. Remove the exhaust gas recirculation (EGR) valve. Refer to Exhaust Gas Recirculation Valve Replacement in Engine Controls - 3.4L.
  24. Remove the MAP sensor and the bracket. Refer to Manifold Absolute Pressure Sensor Replacement in Engine Controls - 3.4L.

  25. Object Number: 261259  Size: SH
  26. Remove the upper intake manifold studs and bolts.

  27. Object Number: 261260  Size: SH
  28. Remove the upper intake manifold.

  29. Object Number: 61855  Size: SH
  30. If you are REPLACING the intake manifold, remove the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls - 3.4L.

  31. Object Number: 261261  Size: SH
  32. Remove the upper intake manifold gasket.
  33. Clean and inspect the upper intake manifold. Refer to Intake Manifold Cleaning and Inspection .

Installation Procedure


    Object Number: 61855  Size: SH
  1. If removed, install the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls - 3.4L.

  2. Object Number: 261261  Size: SH
  3. Install the upper intake manifold gasket.

  4. Object Number: 261260  Size: SH
  5. Install the upper intake manifold.

  6. Object Number: 261259  Size: SH
  7. Install the MAP sensor and the bracket. Refer to Manifold Absolute Pressure Sensor Replacement in Engine Controls - 3.4L.
  8. Install the upper intake manifold studs and bolts. Refer to Intake Manifold Installation .
  9. Install the EGR valve. Refer to Exhaust Gas Recirculation Valve Replacement in Engine Controls - 3.4L.
  10. Connect the vacuum hose connections to the upper intake manifold.
  11. • Heater and air conditioning vacuum source hose
    • Fuel pressure regulator
  12. Connect the vacuum brake booster hose to the upper intake manifold. Refer to Vacuum Brake Booster Hose Replacement in Hydralic Brakes.
  13. Install the MAP sensor and the bracket. Refer to Manifold Absolute Pressure Sensor Replacement in Engine Controls - 3.4L.

  14. Object Number: 261271  Size: SH
  15. Install and connect the emission control vacuum harness.

  16. Object Number: 248103  Size: SH
  17. Connect the vacuum hose to the MAP sensor and the upper intake manifold.

  18. Object Number: 190605  Size: SH
  19. Connect the wiring harness to the MAP sensor.

  20. Object Number: 261282  Size: SH
  21. Install the ignition coil bracket with the coils.
  22. Install the EVAP canister purge solenoid valve. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement in Engine Controls - 3.4L.

  23. Object Number: 261279  Size: SH
  24. Connect the vacuum hoses to the EVAP canister purge solenoid valve.
  25. Connect the throttle body heater hoses. Refer to Throttle Body Heater Inlet Hose Replacement and Throttle Body Heater Outlet Hose Replacement in Engine Cooling.
  26. Connect the engine left side spark plug wire harness attachment clip. Refer to Spark Plug Wire Harness Replacement in Engine Electrical.
  27. Connect the engine left side spark plug wires. Refer to Spark Plug Wire Harness Replacement in Engine Electrical.
  28. Connect the wiring harness connectors to the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls.
  29. Install the accelerator control and cruise control cables with bracket to the throttle body. Refer to Accelerator Control Cable Replacement in Engine Controls - 3.4L.
  30. Install the throttle body air inlet duct. Refer to Air Filter Element Replacement in Engine Controls - 3.4L.
  31. Fill the cooling system with engine coolant. Refer to Cooling System Draining and Filling in Engine Cooling.

Intake Manifold Replacement Lower

Removal Procedure

Important: The fuel injector wiring harness connectors must be connected to their respective fuel injectors. Failure to connect the fuel injector connectors to their respective fuel injectors may result in excessive exhaust emissions and poor engine performance.

  1. Remove the upper intake manifold. Refer to Intake Manifold Replacement .
  2. Remove the engine left side valve rocker arm cover. Refer to Valve Rocker Arm Cover Replacement .
  3. Remove the engine right side valve rocker arm cover. Refer to Valve Rocker Arm Cover Replacement .

  4. Object Number: 190517  Size: SH
  5. Disconnect the wiring harness from the engine coolant temperature (ECT) sensor.

  6. Object Number: 261255  Size: SH

    Important: Use masking tape or another appropriate method in order to identify each fuel injector wiring harness connector cylinder number.

  7. Disconnect and remove the fuel injector, manifold air pressure (MAP) and ECT wiring harness.
  8. Remove the fuel feed and return pipe from the fuel injector rail. Refer to Fuel Hose/Pipes Replacement - Engine Compartment in Engine Controls - 3.4L.

  9. Object Number: 261262  Size: SH
  10. Remove the fuel injector rail. Refer to Fuel Injection Fuel Rail Assembly Replacement in Engine Controls - 3.4L.
  11. Important: Do NOT disconnect the power steering pipes or hoses from the power steering pump.

  12. Remove the power steering pump from the front engine cover and reposition aside. Refer to Power Steering Pump Replacement in Power Steering System.
  13. Disconnect the heater inlet pipe with heater hose from the lower intake manifold and reposition aside. Refer to Heater Inlet Pipe Replacement in Heating, Ventilation and Air Conditioning.
  14. Disconnect the inlet radiator hose from the engine. Refer to Radiator Inlet Hose Replacement in Engine Cooling.

  15. Object Number: 261263  Size: SH
  16. Disconnect the thermostat bypass hose from the lower intake manifold pipe.

  17. Object Number: 261264  Size: SH
  18. Remove the lower intake manifold bolts and discard the bolts.

  19. Object Number: 261265  Size: SH
  20. Remove the lower intake manifold.
  21. Loosen the valve rocker arms and remove the push rods. Refer to Valve Rocker Arm and Push Rod Removal .

  22. Object Number: 61820  Size: SH
  23. Remove the lower intake manifold gaskets and seals.
  24. Clean the lower intake manifold gasket and seal surfaces on the cylinder heads and the engine block.
  25. Clean and inspect the lower intake manifold. Refer to Valve Rocker Arm and Push Rod Removal .
  26. If you are replacing the lower intake manifold, remove the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement in Engine Controls - 3.4L.
  27. If you are REPLACING the lower intake manifold, remove the thermostat. Refer to Engine Coolant Thermostat Replacement in Engine Cooling.

Installation Procedure


    Object Number: 61820  Size: SH
  1. Apply 8-12-mm (0.08-0.11-in) bead of RTV Sealer GM P/N 12346141 (Canadian P/N 89022195) or equivalent on each ridge where front and rear of the lower intake manifold contact the engine block (1).
  2. Install the lower intake manifold gaskets.
  3. Install the push rods and tighten the valve rocker arms. Refer to Valve Rocker Arm and Push Rod Installation .

  4. Object Number: 261265  Size: SH
  5. Install the lower intake manifold. Refer to Intake Manifold Installation .

  6. Object Number: 261264  Size: SH
  7. Install NEW lower intake manifold bolts.
  8. Tighten the lower intake manifold bolts. Refer to Intake Manifold Installation .

  9. Object Number: 261263  Size: SH
  10. Connect the thermostat bypass hose to the lower intake manifold pipe.
  11. Connect the inlet radiator hose from the engine. Refer to Radiator Inlet Hose Replacement in Engine Cooling.

  12. Object Number: 261270  Size: SH
  13. Connect the heater inlet pipe and heater hose to the lower intake manifold. Refer to Heater Inlet Pipe Replacement in Heating, Ventilation and Air Conditioning.
  14. Install the power steering pump to the front engine cover. Refer to Power Steering Pump Replacement in Power Steering System.

  15. Object Number: 261262  Size: SH
  16. Install the fuel injector rail. Refer to Fuel Injection Fuel Rail Assembly Replacement in Engine Controls - 3.4L.
  17. Connect the fuel feed and return pipe to the fuel injector rail. Refer to Fuel Hose/Pipes Replacement - Engine Compartment in Engine Controls - 3.4L.

  18. Object Number: 261255  Size: SH

    Important: The fuel injector wiring harness connectors must be connected to their respective fuel injectors. Failure to connect the fuel injector connectors to their respective fuel injectors may result in excessive exhaust emissions and poor engine performance.

  19. Install and connect the fuel injector, MAP and ECT wiring harness.

  20. Object Number: 190517  Size: SH
  21. Install the wiring harness to the ECT sensor.
  22. Install the engine right side valve rocker arm cover. Refer to Valve Rocker Arm Cover Replacement .
  23. Install the engine left side valve rocker arm cover. Refer to Valve Rocker Arm Cover Replacement .
  24. Install the upper intake manifold. Refer to Intake Manifold Replacement .