GM Service Manual Online
For 1990-2009 cars only

Special Tools

    • J 45027 Tensioner Tool
    • J 45059 Angle Meter

Removal Procedure


    Object Number: 1578296  Size: SH
  1. Remove the hood. Refer to Hood Replacement.
  2. Remove the number 1 cylinder spark plug. Refer to Spark Plug Replacement.
  3. Rotate the crankshaft in the engine rotational direction clockwise, until the number 1 piston is at top dead center (TDC) on the exhaust stroke.
  4. Remove the camshaft cover. Refer to Camshaft Cover Replacement.
  5. Remove the engine front cover. Refer to Engine Front Cover Replacement.
  6. Remove the upper timing chain guide bolts and guide.

  7. Object Number: 1769723  Size: SH

    Important: The timing chain tensioner must be removed to unload chain tension before the timing chain is removed. If it is not, the timing chain will become cocked and it will be difficult to remove.

  8. Remove the timing chain tensioner.

  9. Object Number: 1578298  Size: SH
  10. Install a 24 mm wrench on the hex on the exhaust camshaft in order to hold the camshaft.
  11. Remove and discard the exhaust camshaft actuator bolt (2).
  12. Remove the exhaust camshaft actuator (1, 3) from the camshaft and timing chain.

  13. Object Number: 1578299  Size: SH
  14. Remove the timing chain tensioner guide bolt and guide.

  15. Object Number: 412164  Size: SH
  16. Remove the fixed timing chain guide access plug.

  17. Object Number: 412165  Size: SH
  18. Remove the fixed timing chain guide bolts and guide.

  19. Object Number: 1578297  Size: SH
  20. Install a 24 mm wrench on the hex on the intake camshaft in order to hold the camshaft.
  21. Remove and discard the intake camshaft actuator bolt (2).
  22. Remove the intake camshaft actuator (3), and the timing chain through the top of the cylinder head.

  23. Object Number: 1578300  Size: SH
  24. Remove the timing chain crankshaft sprocket.

  25. Object Number: 1578301  Size: SH
  26. If replacing the balance shaft timing chain and sprocket, perform the following steps, if not proceed to step 10 in the installation procedure.
  27. Remove the balance shaft drive chain tensioner bolts and tensioner.

  28. Object Number: 1578303  Size: SH
  29. Remove the adjustable balance shaft chain guide bolt and guide.

  30. Object Number: 1578302  Size: SH
  31. Remove the small balance shaft drive chain guide bolts and guide.

  32. Object Number: 1578304  Size: SH
  33. Remove the upper balance shaft drive chain guide bolts and guide.

  34. Object Number: 1578305  Size: SH

    Important: It may ease removal of the balance shaft drive chain to get all the slack in the chain between the crankshaft and water pump sprockets.

  35. Remove the balance shaft drive chain (7).
  36. Remove the balance shaft drive sprocket.

Installation Procedure


    Object Number: 1578305  Size: SH
  1. If replacing the balance shaft timing chain, perform the following steps, if not proceed to step 10.
  2. Install the balance shaft drive sprocket.
  3. Important: If the balance shafts are not properly timed to the engine, the engine may vibrate or make noise.

  4. Install the balance shaft drive chain (1) with the colored link lined up with the marks on the balance shaft sprockets and the balance shaft drive sprocket. There are three colored links on the chain. Two are chrome and one is copper. Use the following steps in order to line up the links with the sprockets.
  5. • Place the copper link (5) so that it lines up with the timing mark (2) on the intake side balance shaft sprocket.
    • Working clockwise around the chain, place the chrome link (4) in line with the timing mark (3) on the balance shaft drive sprocket. (Approximately 6 o'clock position on the sprocket.)
    • Place the chain (7) on the water pump drive sprocket. The alignment is not critical.
    • Align the last chrome link (6) with the timing mark (1) on the exhaust side balance shaft drive sprocket.

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1578304  Size: SH
  6. Install the upper balance shaft drive chain guide and bolts.
  7. Tighten
    Tighten the bolts to 15 N·m (11 lb ft).


    Object Number: 1578302  Size: SH
  8. Install the small balance shaft drive chain guide and bolts.
  9. Tighten
    Tighten the bolts to 15 N·m (11 lb ft).


    Object Number: 1578303  Size: SH
  10. Install the adjustable balance shaft chain guide and bolt.
  11. Tighten
    Tighten the bolt to 10 N·m (89 lb in).


    Object Number: 1578301  Size: SH
  12. Reset the timing chain tensioner by performing the following steps:
  13. • Rotate the tensioner plunger 90 degrees in its bore and compress the plunger.
    • Rotate the tensioner back to the original 12 o'clock position and insert a paper clip through the hole in the plunger body and into the hose in the tensioner plunger.
  14. Install the balance shaft drive chain tensioner and bolts.
  15. Tighten
    Tighten the bolts to 10 N·m (89 lb in).

  16. Remove the paper clip from the balance shaft drive chain tensioner.

  17. Object Number: 1825076  Size: SH
  18. Ensure the intake camshaft notch is in the 5 o'clock position (2) and the exhaust camshaft notch is in the 7 o'clock position (1). The number 1 piston should be at TDC, crankshaft key at 12 o'clock.

  19. Object Number: 466551  Size: SH
  20. Install the timing chain drive sprocket to the crankshaft with the timing mark in the 5 o'clock position and the front of the sprocket facing out.

  21. Object Number: 1594347  Size: SH

    Important: 

       • There are 3 colored links on the timing chain. 2 links are of matching color, and 1 link is of a unique color. Use the following procedure to line up the links with the actuators. Orient the chain so that the colored links are visible.
       • Always use new actuator bolts.

  22. Assemble the intake camshaft actuator into the timing chain with the timing mark lined up with the uniquely colored link (1).

  23. Object Number: 1825082  Size: SH
  24. Lower the timing chain through the opening in the cylinder head. Use care to ensure that the chain goes around both sides of the cylinder block bosses (1, 2).
  25. Install the intake camshaft actuator onto the intake camshaft while aligning the dowel pin into the camshaft slot.
  26. Hand tighten the new intake camshaft actuator bolt.

  27. Object Number: 1594349  Size: SH
  28. Route the timing chain around the crankshaft sprocket and line up the first matching colored link with the timing mark on the crankshaft sprocket, in approximately the 5 o'clock position.

  29. Object Number: 1403949  Size: SH
  30. Rotate the crankshaft clockwise to remove all chain slack. Do not rotate the intake camshaft.
  31. Install the adjustable timing chain guide down through the opening in the cylinder head and install the adjustable timing chain bolt.
  32. Tighten
    Tighten the adjustable timing chain guide bolt to 10 N·m (89 lb in).


    Object Number: 1403953  Size: SH

    Important: Always install NEW actuator bolts.

  33. Install the exhaust camshaft actuator into the timing chain with the timing mark lined up with the second matching colored link.

  34. Object Number: 1594351  Size: SH
  35. Install the exhaust camshaft actuator onto the exhaust camshaft, aligning the dowel pin into the camshaft slot.
  36. Using a 23 mm open end wrench, rotate the exhaust camshaft approximately 45 degrees until the dowel pin in the camshaft actuator goes into the camshaft slot.

  37. Object Number: 1403887  Size: SH
  38. When the actuator seats on the cam, tighten the new exhaust camshaft actuator bolt hand tight.
  39. Verify that all of the colored links and the appropriate timing marks are still aligned. If they are not aligned, repeat the portion of the procedure necessary to align the timing marks.

  40. Object Number: 412165  Size: SH
  41. Install the fixed timing chain guide and bolts.
  42. Tighten
    Tighten the fixed timing chain guide bolts to 12 N·m (106 lb in).


    Object Number: 1403955  Size: SH
  43. Install the upper timing chain guide and bolts.
  44. Tighten
    Tighten the upper timing chain guide bolts to 10 N·m (89 lb in).


    Object Number: 797246  Size: SH
  45. Reset the timing chain tensioner by performing the following steps:
  46. 26.1. Remove the snap ring.
    26.2. Remove the piston assembly from the body of the timing chain tensioner.
    26.3. Install the J 45027-2 (2) into a vise.
    26.4. Install the notch end of the piston assembly into the J 45027-2 (2).
    26.5. Using the J 45027-1 (1), turn the ratchet cylinder into the piston.
    26.6. Reinstall the piston assembly into the body of the tensioner.
    26.7. Install the snap ring.

    Object Number: 1769723  Size: SH
  47. Inspect the timing chain tensioner seal for damage. If damaged, replace the seal.
  48. Inspect to ensure all dirt and debris is removed from the timing chain tensioner threaded hole in the cylinder head.
  49. Important: Ensure the timing chain tensioner seal is centered throughout the torque procedure to eliminate the possibility of an oil leak.

  50. Install the timing chain tensioner assembly.
  51. Tighten
    Tighten the timing chain tensioner to 75 N·m (55 lb ft).

  52. The timing chain tensioner is released by compressing it 2 mm (0.079 in), which will release the locking mechanism in the ratchet. To release the timing chain tensioner, use a suitable tool with a rubber tip on the end. Feed the tool down through the cam drive chest to rest on the cam chain. Then give a sharp jolt diagonally downwards to release the tensioner.

  53. Object Number: 1403882  Size: SH
  54. Using a 23 mm wrench, engage the hex on the intake camshaft, and using a torque wrench, tighten the camshaft actuator bolt.
  55. Tighten
    Tighten the intake camshaft position actuator bolt to 30 N·m (22 lb ft), plus 100 degrees using the J 45059 .

  56. Using a 23 mm wrench, engage the hex on the exhaust camshaft, and using a torque wrench, tighten the camshaft actuator bolt.
  57. Tighten
    Tighten the exhaust camshaft position actuator bolt to 30 N·m (22 lb ft), plus 100 degrees using the J 45059 .


    Object Number: 412200  Size: SH
  58. Install the timing chain oiling nozzle.
  59. Tighten
    Tighten the timing chain oiling nozzle bolt to 10 N·m (89 lb in).


    Object Number: 1769728  Size: SH
  60. Apply sealant compound GM P/N 12345382 (Canadian P/N 10953489) to the thread of the timing chain guide bolt access hole plug.
  61. Install the timing chain guide bolt access hole plug.
  62. Tighten
    Tighten the access hole plug to 90 N·m (66 lb ft).

  63. Install the engine front cover. Refer to Engine Front Cover Replacement.
  64. Install the camshaft cover. Refer to Camshaft Cover Replacement.
  65. Install the number 1 cylinder spark plug. Refer to Spark Plug Replacement.
  66. Install the hood. Refer to Hood Replacement.