Rear Seat Belt Buckle Replacement 2 Door

Caution: The seat belt assembly and/or bracket assembly must be replaced as a unit only. Do not substitute parts for any reason, or personal injury could result.

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

1. Fold the rear seat back.
2. Pull the rear seat release handle and raise the rear seat.
3. Unclip the support rod from the bottom of the rear seat and the support seat.



4. Remove one rear anchor bolt from each rear seat hinge (1).
5. Lower the rear seat.



6. Gently pry the hinge cover (2) from each rear seat hinge (1).



7. Remove one front anchor bolt from each rear seat hinge (1).
8. Remove the seat from the vehicle.



9. Remove one clip and pin (1) from each rear seat hinge (2).
10. Remove the hinges (2) from the seat.
11. Remove one clip, the pin (1) and the support rod from the rear seat.
12. Remove one clip, the pin and the rear seat release handle from the seat.
13. Remove one screw from each rubber bumper.
14. Remove the bumpers from the seat.
15. Remove six screws and the rear seat cushion trim cover from the rear seat.



16. Remove one anchor bolt (1) from the bottom of the rear seat cushion securing the rear seat belt buckle to the seat.
17. Remove the rear seat belt buckle from the seat.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Install the rear seat belt buckle to the rear seat. Secure with one anchor bolt (1).

Tighten
Tighten the rear seat belt buckle anchor bolt to 45 N·m (33 lb ft).

2. Install the rear seat cushion trim cover to the rear seat. Secure with six screws.
3. Connect the rubber bumpers to the seat. Secure each bumper with one screw.
4. Install the rear seat release handle. Secure the handle with one pin and clip.
5. Install the support rod to the rear seat. Secure the rod with one pin and clip.



6. Install the rear seat hinges (2) to the seat. Secure each hinge with one pin (1) and clip.
7. Install the rear seat to the vehicle. Secure the seat with one front anchor bolt to each rear seat hinge (2).

Tighten
Tighten the rear seat front anchor bolts to 25 N·m (19 lb ft).




8. Install the hinge cover (2) to each rear seat hinge (1).
9. Raise the rear seat and support it with the rear seat support rod.
10. Install one rear anchor bolt to each rear seat hinge.

Tighten
Tighten the rear seat rear anchor bolts to 25 N·m (19 lb ft).

11. Clip the support rod to the bottom of the rear seat and lower the seat.
12. Raise the rear seat back into the upright position.

Rear Seat Belt Buckle Replacement 4 Door

Caution: The seat belt assembly and/or bracket assembly must be replaced as a unit only. Do not substitute parts for any reason, or personal injury could result.

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

1. Remove the rear seat back cushion cover. Refer to Seats in Body and Accessories.



2. Pull back the rear seat cushion cover (2) in order to expose the seat belt buckle anchor bolts (1).
3. Remove the rear seat belt buckle anchor bolt and remove the buckle from the rear seat.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Install the rear seat belt buckle to the rear seat. Secure the buckle with one bolt.

Tighten
Tighten the rear seat belt buckle anchor bolt to 45 N·m (33 lb ft).

2. Put the rear seat cushion cover (2) back in place with the hooks on the seat frame (4).
3. Install the rear seat back cushion cover. Refer to Seats in Body and Accessories.