Refer to
Fuel Controls
.
Circuit Description
The Powertrain Control Module (PCM) has four fuel injector driver circuits, each of which controls a fuel injector. The PCM monitors the current in each driver circuit and is able to control the driver circuit. The current through each driver can rise to a peak of 2 amps in order to quickly open the fuel injectors. The current can reduce to 1/2 amp to hold the fuel injectors open. This is called peak and hold. If the current cannot reach a 2-amp peak, a DTC is set. This DTC is also set if a fuel injector driver is shorted to voltage.
Conditions for Setting the DTC
| • | Injector current is less than 4 amps. |
| • | Battery voltage is more than 9 volts. |
| • | Above conditions met for 10 seconds. |
Action Taken When the DTC Sets
| • | The malfunction indicator lamp (MIL) illuminates. |
| • | The PCM records the operating conditions at the time when the diagnostic fails. This information stores in the Freeze Frame and Failure Records buffers. |
| • | A history DTC stores. |
| • | The coolant fan turns ON. |
Conditions for Clearing the MIL/DTC
| • | The MIL will turn OFF after three consecutive ignition cycles in which the diagnostic runs without a fault. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | The MIL/DTCs can be cleared by using the scan tool. |
Diagnostic Aids
An injector driver circuit that is open or shorted to voltage will cause a DTC P0200 to set and will also cause a misfire due to an inoperative injector. A misfire DTC should also be set indicating which injector is inoperative.
Long term and short term fuel trims that are excessively high or low are a good indication that an injector is faulty. Use Fuel Injector Solenoid Coil Test to check for faulty injectors.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
-
The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored on the scan tool for later reference.
-
This step determines if DTC P0200 is the result of a hard failure or an intermittent condition.
-
Test the harness wiring and for PCM control of the injectors using test light J 34780-2. If the tests light blinks, the PCM and wiring to the injectors are OK. Fuel Injector Solenoid Coil Test will check if injectors are faulty.
-
Whether the test light was ON steady or OFF while cranking the engine narrows the possible faults down to just a few.
-
Because the test light was ON steady, voltage to the injector is OK, but the driver circuit is grounded at all times. This step determines if the circuitry is shorted to ground or the PCM is faulty.
-
Replacement PCM's must be reprogrammed. Refer to the latest Techline information for programming procedures.
-
Determines if voltage is available to the injector. Voltage is supplied through the fuel pump relay so the engine must be cranked to see voltage at the injector.
-
This step determines if the driver circuit is open or shorted to voltage or if the PCM is faulty.
-
Since voltage is supplied to the injector on a single circuit before the injector harness, the fault could only be a poor connection or open in the injector harness. An open before the harness would result in a Cranks But Won't Run complaint.
-
Check the injector electrical connector, the injector harness connector and the PCM for poor connections or corroded terminals.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | |||
2 | Will the engine start? | -- | ||
Does DTC P0200 reset? | -- | |||
4 |
Does P0200 Reset? | -- | ||
Does the injector test light blink on all test? | -- | |||
Note whether the injector test light was OFF or ON steady in step 5 for the injector connector that did not blink. Was the injector test light ON steady while cranking the engine? | -- | |||
Does the injector test light illuminate? | -- | |||
8 | Check for a short to ground in the injector driver circuit and repair as necessary. Was a repair necessary? | -- | ||
Replace the PCM. Is the action complete? | -- | -- | ||
Does the test light illuminate while cranking? | -- | |||
Is the test light OFF while cranking? | -- | |||
Repair the open in the ignition feed circuit in the injector harness. Is the action complete? | -- | -- | ||
Check the injector driver circuit for an open or faulty connection. Was a problem found? | -- | |||
14 | Repair the short to voltage in the injector driver circuit. Is the action complete? | -- | -- | |
15 | Repair the open or faulty connection in the injector driver circuit. Is the action complete? | -- | -- | |
16 |
Does the scan tool indicate that this diagnostic has ran and passed? | -- | ||
17 | Check if any additional DTC's are set. Are any DTC's displayed that have not been diagnosed? | -- | Go to applicable DTC table | System OK |
