GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 1998 🢒 Sunfire 🢒 Engine 🢒 Engine Controls - 2.2L 🢒 Restricted Exhaust System Check

System Description
Object Number: 20425 Size: SH

Proper diagnosis for a restricted exhaust system is essential before any components are replaced. Using the Restricted Exhaust System Check table should determine if the exhaust system is restricted. The best place for checking the exhaust system is at the O2S 1 location. Once the test is completed, coat threads with anti-seize compound P/N 5613695 or equivalent prior to O2S re-installation.

Test Description

The numbers below refer to the step numbers on the Diagnostic Table.

  1. The OBD System Check prompts you to complete some of the basic checks and to store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data captured when the malfunction occurred. The scan tool stores this data for later reference.

    2.

  2. The exhaust system under normal conditions has very low back pressure. If the exhaust system is restricted, a noticeable increase in exhaust pressure is noticed on the gauge.

    3.

  3. If no high back pressure is found at idle, increasing the engine speed to 3,000 RPM may find a slight restriction. The added engine speed increases the exhaust flow which will help determine if there is a slight restriction.

    4.

  4. This step will isolate the catalyst from the remainder of the exhaust system.

    5.

  5. If the muffler is plugged, check the catalytic convertor to see if the internal material has broken apart.

Restricted Exhaust System Check

Step

Action

Value(s)

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check for 2.4L or Powertrain On Board Diagnostic (OBD) System Check for 2.2L

2

    Caution: Avoid contact with moving parts and hot surfaces while working around a running engine in order to prevent physical injury.

  1. Carefully remove the O2S 1 sensor from the exhaust manifold. Refer to Oxygen Sensor Replacement for 2.4L or Oxygen Sensor Replacement for 2.2L for the removal procedure.
  2. Install the J 35314-A exhaust back pressure tester in place of the O2S 1.

Is the action complete?

--

Go to Step 3

--

3

  1. Start the engine.
  2. Idle the engine in park or neutral.
  3. Observe the exhaust system back pressure reading on the gauge. The reading should not exceed the specified value.

Does the reading exceed the specified value?

3.4 kPa (0.5 psi)

Go to Step 5

Go to Step 4

4

  1. Increase the engine speed to the first specified value.
  2. Observe the back pressure reading on the gauge. The reading should not exceed the second specified value.

Does the reading exceed the specified value?

3,000 RPM

5 kPa (0.75 psi)

Go to Step 5

Go to Step 9

5

  1. Turn OFF the ignition switch.

    2. Caution: Avoid contact with moving parts and hot surfaces while working around a running engine in order to prevent physical injury.

  2. Disconnect and remove the exhaust back pressure tester.
  3. Install the O2S 1 sensor. Refer to Oxygen Sensor Replacement for 2.4L or Oxygen Sensor Replacement for 2.2L for the installation procedure.
  4. Remove the HO2S 2 sensor. Refer to Heated Oxygen Sensor Replacement for 2.4L or Heated Oxygen Sensor Replacement for 2.2L for the removal procedure.
  5. Install the exhaust back pressure tester in place of the HO2S 2 sensor.
  6. Start the engine.
  7. Idle the engine in park or neutral.
  8. Observe the exhaust system back pressure reading on the gauge. The reading should not exceed the specified value.

Does the reading exceed the specified value?

3.4 kPa (0.5 psi)

Go to Step 7

Go to Step 6

6
  1. Increase the engine speed to the first specified value.
  2. Observe the back pressure reading on the gauge. The reading should not exceed the second specified value.

Does the reading exceed the specified value?

3,000 RPM

5 kPa (0.75 psi)

Go to Step 7

Go to Step 8

7

  1. Turn OFF the ignition switch.

    2. Caution: Avoid contact with moving parts and hot surfaces while working around a running engine in order to prevent physical injury.

  2. Check the entire exhaust system for the following conditions:
    3. • Collapsed pipe
    • Heat distress
    • Internal muffler malfunction
  3. Replace any malfunctioning component.

Did any component require replacement?

--

Go to Step 9

Go to Step 8

8

Caution: Avoid contact with moving parts and hot surfaces while working around a running engine in order to prevent physical injury.

Check the exhaust system between the engine and the catalytic convertor, if OK replace the catalytic converter. Refer to Catalytic Converter Replacement for the replacement procedure.

Is the action complete?

--

Go to Step 9

--

9

    Caution: Avoid contact with moving parts and hot surfaces while working around a running engine in order to prevent physical injury.

  1. Remove the exhaust back pressure gauge if installed.
  2. Install the O2S 1 sensor if the O2S 1 sensor is still removed. Refer to Oxygen Sensor Replacement for 2.4L or Oxygen Sensor Replacement for 2.2L for the installation procedure.
  3. Install the HO2S sensor if the HO2S 2 sensor is still removed. Refer to Heated Oxygen Sensor Replacement for 2.4L or Heated Oxygen Sensor Replacement for 2.2L for the installation procedure.
  4. Start the engine.
  5. Idle the engine until the normal operating temperature is reached.
  6. Check to see if any DTCs are set.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to the applicable DTC table

System OK