DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected. Pontiac Sunfire 2000

For 1990-2009 cars only

Makes 🢒 Pontiac 🢒 2000 🢒 Sunfire 🢒 Engine 🢒 Engine Controls - 2.4L 🢒 DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected

Engine Controls Components
EVAP and EGR Controls
OBD II Symbol Description Notice
Powertrain Control Module Connector End Views
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The evaporative system includes the following components:

•	The fuel tank

•	The EVAP vent solenoid

•	The fuel tank pressure sensor

•	The fuel pipes and hoses

•	The fuel vapor lines

•	The fuel cap

•	The EVAP canister

•	The purge lines

•	The EVAP canister purge solenoid valve

•	The EVAP service port

The evaporative emission (EVAP) system is checked by applying vacuum to the EVAP system and by monitoring for a vacuum decay. The Powertrain Control Module (PCM) monitors the vacuum level through the fuel tank pressure sensor signal. At an appropriate time, the EVAP canister purge solenoid valve and the EVAP vent solenoid are turned ON, allowing the engine to draw a small vacuum on the entire evaporative emission system. Once the desired vacuum level has been achieved, the EVAP canister purge solenoid valve turns OFF, sealing the system. A small leak in the system will cause DTC P0442 to set.

Conditions for Running the DTC

•	DTCs P0105, P0107, P0108, P0112, P0113, P0117, P0118, P0122, P0123, P0125, P0131, P0132, P0133, P0134, P0452, P0453, P0502, P0503, P0601, P0602, P1621, and P1133 are not set.

•	The BARO is more than 75 kPa.

•	The intake air temperature (IAT) is between 5°C and 29°C (41°F and 84°F) at engine start up.

•	The engine coolant temperature (ECT)is between 5°C and 29°C (41°F and 84°F) at engine start up.

•	The intake air temperature (IAT) is not more than 1°C (2°F) more than the engine coolant temperature (ECT) at start up.

•	The engine coolant temperature (ECT) is not more than 7°C (12°F) more than the intake air temperature (IAT) at start up.

•	The fuel tank level is between 26 percent and 74 percent.

•	The TP sensor is between 7 percent and 35 percent.

Conditions for Setting the DTC

The EVAP system is unable to detect vacuum during the diagnostic test.

Action Taken When the DTC Sets

•	The malfunction indicator lamp (MIL) will illuminate.

•	The PCM will record the operating conditions at the time that the diagnostic fails. The Freeze Frame and Failure Records buffers will store this information.

•	A history DTC stores.

Conditions for Clearing the MIL/DTC

•	The MIL will turn OFF after 3 consecutive ignition cycles in which the diagnostic runs a pass.

•	A history DTC will clear after 40 consecutive warm up cycles without a malfunction.

•	Use a scan tool to clear the DTCs.

Diagnostic Aids

Although this DTC is considered a type A diagnostic, refer to Serial Data Communications , this DTC acts like a type B diagnostic under certain conditions. Whenever this diagnostic reports that the system has passed, or if the battery is disconnected, the diagnostic must fail twice before setting a DTC. The initial failure does not report to the diagnostic executive or display on a scan tool. A passing system always reports to the diagnostic executive immediately.

If a DTC P0461 is set along with an EVAP System DTC, the EVAP DTC cannot be considered valid until you repair and clear DTC P0461.

Inspect for the following conditions:

•	Any missing or damaged O-rings at the fuel vapor and the EVAP purge line canister fittings.

•	A cracked or a punctured EVAP canister.

•	A damaged source vacuum line, EVAP purge line, EVAP vent hose, or fuel tank vapor line.

•	A poor electrical terminal connection at the PCM. Inspect the harness electrical connectors for the following conditions:

-	Backed out terminals

-	Improper mating

-	Broken locks

-	Improperly formed connectors

-	Damaged terminals

-	A poor terminal to wire connection

•	A damaged harness. Inspect the wiring harness for an intermittent open or shorted circuit in the following components:

-	EVAP vent solenoid

-	EVAP canister purge solenoid valve

-	Fuel tank pressure sensor

•	Refer to Evaporative Emission System Cleaning for further procedure.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

If a vent solenoid or an EVAP canister purge solenoid valve electrical malfunction is present, the purge system will not operate correctly. Repairing the electrical malfunction will very likely correct the condition that set DTC P0442.

This step tests the fuel tank pressure sensor at the ambient pressure.

This step verifies that the fuel tank pressure sensor accurately reacts to the EVAP system pressure changes.

This step insures proper system integrity.

DTC P0442-Evaporative Emission (EVAP) Control System - Small Leak Detected

Step

Action

Value(s)

Yes

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Turn ON the ignition, with the engine OFF.
Install a scan tool.

Is DTC P0452, P0453 or P0461 also set?

Go to Diagnostic Trouble Code (DTC) List/Type

Go to Step 3

Command the EVAP canister purge solenoid valve ON and OFF with the scan tool.
Command the vent solenoid ON and OFF with the scan tool.

Does the purge valve and vent solenoid click ON and OFF?

Go to Step 4

Go to Powertrain Control Module Outputs Diagnosis

Turn OFF the ignition.
Disconnect the vapor line from the fuel tank at the EVAP canister.
Turn ON the ignition, with the engine OFF.
Observe the Fuel Tank Pressure sensor value with the scan tool.

Is the Fuel Tank Pressure within the specified value range?

-0.32 - +0.32 kPa

(-1.28 - +1.28 in. H2O)

Go to Step 6

Go to Step 5

Turn OFF the ignition.
Inspect the EVAP vapor line from the fuel tank to the EVAP canister for the following conditions.

•	Pinched vapor line

•	Kinked vapor line

•	Plugged vapor line

If a problem is found, repair as necessary.

Did you find and correct the condition?

Go to Step 14

Go to DTC P0452 Fuel Tank Pressure Sensor Circuit Low Voltage

DTC P0453 Fuel Tank Pressure Sensor Circuit High Voltage

Important: : Before continuing with this diagnosis, zero the EVAP Pressure and Vacuum gauges on the J 41413 EVAP pressure/purge Diagnostic Station. Then, read the temperature variation instructions Refer to the tool operating instructions.

Reconnect all the EVAP hardware that was previously disconnected.
Connect the J 41413 EVAP pressure/purge Diagnostic Station to the EVAP service port.
Command the EVAP vent solenoid ON (closed) with the scan tool.

Important: Do not exceed the pressure given in the first specified value.

Pressurize the EVAP system to the first specified value using the J 41413 EVAP pressure/purge Diagnostic Station (monitor the pressure by using the gauge on the station with the switch in the HOLD position).
Observe the Fuel Tank Pressure on the scan tool.

Is the Fuel Tank Pressure at the second specified value?

1.25 kPa

(5 in. H2O)

.96 kPa

(3.85 in. H2O)

Go to Step 7

Go to DTC P0452 Fuel Tank Pressure Sensor Circuit Low Voltage

DTC P0453 Fuel Tank Pressure Sensor Circuit High Voltage

Important: Review the temperature variation instructions included with the J 41413 EVAP pressure/purge Diagnostic Station before performing this step.

Command the EVAP vent solenoid ON (closed) with the scan tool.

Important: Do not exceed the pressure given in the first specified value.

Pressurize the EVAP system to the first specified value by using the J 41413 EVAP pressure/purge Diagnostic Station (monitor the pressure by using the gauge on the station).
Switch the rotary switch on the station to HOLD and observe the EVAP pressure gauge.

Does the pressure decrease to less than the second specified value within 2 minutes?

3.74 kPa

(15 in. H2O)

2.49 kPa

(10 in. H2O)

Go to Step 9

Go to Step 8

Important: Review the temperature variation instructions included with the J 41413 EVAP pressure/purge Diagnostic Station before performing this step.

Turn OFF the ignition.
Install the J 41415-40 Fuel Tank Cap Adapter.
Connect the J 41413 EVAP pressure purge Diagnostic Station to the Fuel Tank Cap Adapter
Turn ON the ignition, with the engine OFF.
Command ON the scan tools EVAP SYSTEM SEAL function to seal the EVAP system.

Important: Do not exceed the pressure given in the first specified value.

Pressurize the EVAP system to the first specified value by using the J 41413 EVAP pressure/purge Diagnostic Station (monitor the pressure by using the gauge on the station).

Does the pressure decrease to less than the second specified value within 2 minutes?

3.74 kPa

(15 in. H2O)

2.49 kPa

(10 in. H2O)

Go to Step 12

Go to Diagnostic Aids

Disconnect the following lines from the EVAP canister.

•	EVAP purge line

•	Fuel tank vapor line

Block the fuel tank vapor line fitting on the canister.
Connect a hand vacuum pump to the EVAP purge line fitting on the canister.
Ensure that the EVAP vent solenoid is still commanded ON (closed).
Attempt to apply vacuum to the canister.

Can the specified vacuum be maintained?

16.95 kPa

(5 in. Hg)

Go to Step 12

Go to Step 10

Turn OFF the ignition.
Visually/physically inspect for the following conditions:

•	Disconnected vent hose

•	Damaged vent hose

•	A damaged EVAP canister

If a problem is found, repair the as necessary.

Did you find and correct the condition?

Go to Step 13

Go to Step 11

Notice: The EVAP canister may have released carbon particles which caused this part to fail and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.

Replace the EVAP vent solenoid. Refer to Evaporative Emission Vent Valve Replacement . .
If carbon particles are found in the component refer to Evaporative Emission System Cleaning .

Did you complete the replacement?

Go to Step 13

Turn OFF the ignition.
Visually/physically inspect for the following conditions:

•	A malfunctioning fuel cap

•	Incorrect fuel cap

•	A leaking fuel tank filler neck

•	A leaking fuel tank vapor line

•	A damaged EVAP purge line

If a problem is found, repair the as necessary.
Reconnect all the EVAP hardware that was previously disconnected.
Turn ON the ignition, with the engine OFF.
Command the EVAP vent solenoid ON (closed) with the scan tool.
With the J 41413 EVAP pressure/purge Diagnostic Station connected to the EVAP system, leave the station control knob in the pressurized position.
Use the J 41416 ultrasonic leak detector to locate and repair the leak in the EVAP system (it may be necessary to partially lower the fuel tank in order to examine the top tank connections).

Did you complete the repair?

Go to Step 13

Important: Review the temperature variation instructions included with the J 41413 EVAP pressure/purge Diagnostic Station before performing this step.

Reconnect all the EVAP hardware that was previously disconnected.
Turn ON the ignition, with the engine OFF.
Command the EVAP vent solenoid ON (closed) with the scan tool.

Important: Do not exceed the pressure in the first specified value.

Pressurize the EVAP system to the first specified value by using the J 41413 EVAP pressure/purge Diagnostic Station (monitor the pressure by using the gauge on the station).
Switch the rotary switch on the station to HOLD and observe the EVAP pressure gauge.

Does the pressure decrease to less than the second specified value within 2 minutes?

3.74 kPa

(15 in. H2O)

2.49 kPa

(10 in. H2O)

Go to Step 3

Go to Step 14

Use a scan tool to clear the DTCs.
Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 3

System OK