Water Pump Replacement 2.2L

1. Drain the cooling system. Refer to Cooling System Draining and Filling .



2. Loosen the coolant pump pulley bolts.
3. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 2.2L.
4. Remove the coolant pump pulley bolts.
5. Remove the coolant pump pulley.



6. Remove the coolant pump bolts.
7. Remove the coolant pump and the gasket.
8. Completely clean the sealing surfaces of the coolant pump and the engine block.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Using a new gasket, install the coolant pump and the attaching bolts. Coat the bolt threads with pipe sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent.

Tighten
Tighten the coolant pump bolts to 25 N·m (18 lb ft).




2. Install the coolant pump pulley and bolts.

Tighten
Tighten the coolant pump pulley bolts to 30 N·m (22 lb ft).

3. Install the accessory drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 2.2L.
4. Refill the cooling system. Refer to Cooling System Draining and Filling .
5. Start the engine. After the engine reaches normal operating temperature, check for coolant leaks.

Water Pump Replacement 2.4L

1. Drain the cooling system. Refer to Cooling System Draining and Filling .
2. Remove the exhaust manifold. Refer to Exhaust Manifold Replacement in Engine Exhaust.
3. Remove the coolant outlet pipe. Refer to Radiator Outlet Pipe Replacement .
4. Disconnect the heater hose quick connect from the heater outlet pipe.
5. Remove the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical.



6. Remove the water pump cover-to-cylinder block bolts.
7. Remove water pump cover pipe bracket bolt (Bellhousing bolt).



8. Remove the water pump-to-timing chain housing nuts.
9. Remove the water pump and cover assembly.
10. Remove the water pump cover-to-coolant pump assembly bolts.
11. Clean all sealing surfaces.

Important: Before you install the coolant pump, read the entire procedure. Follow the tightening sequences in order to avoid part damage and to provide proper sealing.




1. Install the water pump cover to the water pump assembly.
2. Install the pump cover bolts. Hand tighten the bolts.
3. Install water pump/cover assembly.



4. Install the cover-to-block bolts. Hand tighten the bolts.
5. Install the coolant pump-to-timing chain housing nuts. Hand tighten the nuts.
6. Install water pump cover pipe bolt (Bellhousing Bolt).




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Torque in sequence as follows:

7.1.	Tighten the pump assembly-to-timing chain housing nuts.

Tighten
Tighten nuts to 26 N·m (19 lb ft).

7.2.	Tighten the pump cover-to-pump assembly bolts.

Tighten
Tighten the bolts to 14 N·m (10 lb ft).

7.3.	Tighten the coolant pump cover-to-engine block bolts. Tighten the bottom bolt first.

Tighten
Tighten bolts to 26 N·m (19 lb ft).

8. Install heater hose to water pump cooling pipe.
9. Install radiator outlet pipe.Refer to Radiator Outlet Pipe Replacement .
10. Install the exhaust manifold and install new gaskets. Refer to Exhaust Manifold Replacement in Engine Exhaust.
11. Install oil level indicator tube and indicator.
12. Connect the brake vacuum pipe to the cam housing.
13. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
14. Install catalytic converter. Refer to Catalytic Converter Replacement in Engine Exhaust.
15. Install the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical - 2.4 L.
16. Lower the vehicle.
17. Fill the cooling system. Refer to Cooling System Draining and Filling .
18. Inspect the system for leaks.