Tools Required

J 25070 Heat Gun

1. When replacing an emblem/nameplate, do the following:

1.1.	Use tape to protect the mounting surface during removal.

1.2.	Use tape for alignment marks for installation of the emblem/nameplate.

2. To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070 .
3. Apply the heat using a circular motion for about 30 seconds holding the J 25070 approximately 152 mm (6 in) from the surface.




Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

4. Use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
5. When replacing, remove all adhesive as follows:

•	For body panels, use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.

•	For plastic panels, use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a, 50/50 mixture, by volume of isopropyl alcohol and water to remove the adhesive.

Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

1. Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a, 50/50 mixture, by volume of isopropyl alcohol and water to clean the area.

2. Dry the area thoroughly.
3. If the location of the emblem/nameplate has not been marked, apply tape and use the following dimensions:



4. For the CHEVROLET emblem/nameplate, install to the following dimensions:

•	Dimension (a) is 41 mm (1.563 in) from the right edge of the rear compartment lid to the nameplate.

•	Dimension (b) is 15 mm (0.563 in) from the bottom edge of the rear compartment lid to the nameplate.




5. For the CAVALIER LS emblem/nameplate, install to the following dimensions:

•	Dimension (a) is 43 mm (1.688 in) from the left edge of the rear compartment lid to the nameplate.

•	Dimension (b) is 45 mm (1.750 in) from the bottom edge of the rear compartment lid to the nameplate.

•	Dimension (c) is 235 mm (9.250 in) from the left edge of the rear compartment lid to the LS nameplate.

•	Dimension (d) is 45 mm (1.750 in) from the bottom edge of the rear compartment lid to the nameplate.




6. For the CAVALIER 2.4Z emblem/nameplate, install to the following dimensions:

•	Dimension (a) is 15 mm (0.590 in) from the bottom edge of the rear compartment lid to the emblem/nameplate.

•	Dimension (b) is 9 mm (0.354 in) from the CAVALIER emblem/nameplate to the 2.4Z emblem/nameplate.

•	Dimension (c) is 15 mm (0.590 in) form the bottom edge of the rear compartment lid to the emblem/nameplate.

•	Dimension (d) is 350 mm (13.779 in) from the right edge of the rear compartment lid to the beginning of the emblem/nameplate.




7. For the CHEVY BOW TIE emblem (1), install to the following dimensions:

•	The emblem (1) is centered below the lock cylinder.

•	The emblem (1) is 100 mm (3.397 in) from the bottom edge of the rear compartment lid to the bottom of the emblem.

8. Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
9. Ensure that the temperature of the emblem/nameplate is approximately 29-32°C (85-90°F).

Important: Do not touch the adhesive backing on the emblem/nameplate.

10. Remove the protective liner from the back of the emblem/name plate.
11. Position the emblem/nameplate to the location marks and press the emblem/nameplate to the mounting surface.
12. Apply equal pressure along the emblem/nameplate to uniformly bond the item to the mounting surface.
13. Remove the protective tape from the mounting surface.