GM Service Manual Online
For 1990-2009 cars only

System Description

The powertrain control module (PCM) uses information from the ignition control (IC) module and the camshaft position (CMP) sensor in order to determine when an engine misfire is occurring. By monitoring variations in the crankshaft rotation speed for each cylinder, the PCM is able to detect individual misfire events. A misfire rate that is high enough can cause the 3-way catalytic converter (TWC) to overheat under certain driving conditions. The malfunction indicator lamp (MIL) will flash ON and OFF when the conditions for TWC overheating are present. If the PCM detects a misfire rate sufficient to cause emission levels to exceed mandated standards, DTC P0300 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0300 Engine Misfire Detected

Conditions for Running the DTC

    • DTC P0016, P0101, P0102, P0103, P0107, P0108, P0116, P0117, P0118, P0120, P0125, P0128, P0220, P0315, P0335, P0336, P0340, P0341, P0608, P1125, P1516, P2101, P2108, P2120, P2125, P2135, or P2138 is not set.
    • The engine speed is between 525-5,700 RPM.
    • The ignition voltage is between 9-18 volts.
    • The engine coolant temperature (ECT) is between -7 and +123°C (+19 and +253°F).
    • If the ECT is less than -7°C (19°F) at engine start-up, the diagnostic will be disabled until the ECT is more than 21°C (69°F).
    • The fuel level is more than 10 percent.
    • The antilock brake system (ABS) and the traction control system are not active.
    • The transmission is not changing gears.
    • The PCM is not in fuel shut-off or decel fuel cut-off mode.
    • The PCM is not receiving a rough road signal.
    • The power management is not active.
    • Excessive drive wheel slip is not detected.

Conditions for Setting the DTC

The PCM is detecting a crankshaft rotation speed variation indicating a misfire sufficient to cause emission levels to exceed mandated standards.

Action Taken When the DTC Sets

The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second ignition cycle the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. The control module illuminates the malfunction indicator lamp (MIL) when one of the following occur:

    • The control module detects the same misfire failure during 2 consecutive trips.
    • The control module detects any misfire failure during any subsequent trip if the conditions at the time of failure meet the following criteria:
       - The engine load is within 20 percent of the previous test that failed.
       - The engine speed is within 375 RPM of the previous test that failed.
       - The engine coolant temperature is in the same range of the previous test that failed.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

    • Excessive vibration from sources other than the engine could cause DTC P0300 to set. The following are possible sources of vibration:
       - Variable thickness brake rotors--Refer to Symptoms - Hydraulic Brakes .
       - Worn or damaged accessory drive belt--Refer to Symptoms - Engine Mechanical .
    • Spray water on the secondary ignition components using a spray bottle. Look and listen for arcing or misfiring.

If condition is intermittent or not active, refer to Testing for Intermittent Conditions and Poor Connections .

Test Description

The number below refers to the step number on the diagnostic table.

  1. If the actual crankshaft position (CKP) variation values are not within the learned values, the misfire counters may increment.

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Important: You must perform the crankshaft position (CKP) system variation learn procedure before proceeding with this diagnostic table. Refer to Crankshaft Position System Variation Learn .

  1. Start the engine.
  2. Allow the engine to idle or operate within the conditions listed in the Freeze Frame/Failure Records.
  3. Monitor all of the Misfire Current counters with the scan tool.

Are any of the Misfire Current counters incrementing?

--

Go to Step 3

Go to Diagnostic Aids

3

Are any other DTCs set?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

Go to Step 4

4

Can any abnormal engine noise be heard?

--

Go to Symptoms - Engine Mechanical

Go to Step 5

5

Observe the Misfire History Cyl# parameter with a scan tool.

Does more than one cylinder indicate a large count value for the Misfire History Cyl# parameter?

--

Go to Step 6

Go to Step 8

6

Are the Misfire History Cyl# counts indicated for companion cylinders 1/4 or 2/5 or 3/6?

--

Go to Step 8

Go to Step 7

7

Inspect the following components:

    • The vacuum hoses and seals for splits, restrictions, and improper connections--Refer to Evaporative Emissions Hose Routing Diagram .
    • The throttle body and intake manifold for vacuum leaks
    • The crankcase ventilation system for vacuum leaks--Refer to Crankcase Ventilation System Inspection/Diagnosis .
    • The Exhaust Gas Recirculation (EGR) System components for vacuum leaks or excessive flow--Refer to Exhaust Gas Recirculation (EGR) System Cleaning .
    • The powertrain control module (PCM) grounds for corrosion and loose connections--Refer to Ground Distribution Schematics .
    • The Exhaust System for restrictions--Refer to Restricted Exhaust .
    • The fuel for contamination--Refer to Alcohol/Contaminants-in-Fuel Diagnosis .

Did you find and correct the condition?

--

Go to Step 20

Go to Step 8

8

  1. Turn OFF the ignition.
  2. Disconnect the spark plug wire from the spark plug that corresponds to the Misfire Current counters that were incrementing. Refer to Spark Plug Wire Replacement .
  3. Install the J 26792 Spark Tester to a good ground.
  4. Jumper the spark plug end of the companion cylinder ignition wire to engine ground. The companion cylinder is the cylinder that shares the same ignition coil.
  5. Start the engine.

Does the spark jump the tester gap, and is the spark consistent?

--

Go to Step 10

Go to Step 9

9

  1. Remove the spark plug wire for the affected cylinder. Refer to Spark Plug Wire Replacement .
  2. Inspect the spark plug wire. Refer to Spark Plug Wire Inspection .
  3. Measure the resistance of the spark plug wire with a DMM. Refer to Ignition System Specifications .

Is the spark plug wire resistance less than or equal to the specified resistance?

--

Go to Electronic Ignition (EI) System Diagnosis

Go to Step 19

10

  1. Remove the spark plug from the cylinder that indicated a misfire.
  2. Inspect the spark plug. Refer to Spark Plug Wire Inspection .

Does the spark plug appear to be OK?

--

Go to Step 11

Go to Step 12

11

  1. Exchange the suspected spark plug with another cylinder that is operating properly. Refer to Spark Plug Replacement .
  2. Operate the vehicle under the same conditions that the misfire occurred.

Did the misfire move with the spark plug?

--

Go to Step 18

Go to Step 15

12

Is the spark plug oil or coolant fouled?

--

Go to Symptoms - Engine Mechanical

Go to Step 13

13

Is the spark plug gas fouled?

--

Go to Step 16

Go to Step 14

14

Does the spark plug show any signs of being cracked, worn, or improperly gapped?

--

Go to Step 17

Go to Step 15

15

Perform the fuel injector coil test. Refer to Fuel Injector Diagnosis .

Did you find and correct the condition?

--

Go to Step 20

Go to Symptoms - Engine Mechanical

16

Perform the fuel system diagnosis. Refer to Fuel System Diagnosis .

Did you find and correct the condition?

--

Go to Step 20

Go to Symptoms - Engine Mechanical

17

Replace or gap the spark plug. Refer to Spark Plug Replacement .

Did you complete the replacement?

--

Go to Step 20

--

18

Replace the faulty spark plug. Refer to Spark Plug Replacement .

Did you complete the replacement?

--

Go to Step 20

--

19

Replace the faulty spark plug wires. Refer to Spark Plug Wire Replacement .

Did you complete the replacement?

--

Go to Step 20

--

20

Was the customer concern the malfunction indicator lamp (MIL) flashing?

--

Go to Step 21

Go to Step 22

21

  1. Operate the vehicle at the specified value for 4 minutes.
  2. If the customer concern is the MIL flashing, operate the vehicle within the Conditions for Running the DTC P0420, as specified in the supporting text. Refer to Diagnostic Trouble Code (DTC) List - Vehicle .

Does the DTC run and pass?

2,500 RPM

Go to Step 22

Go to Diagnostic Trouble Code (DTC) List - Vehicle

22

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 23

23

In order to ensure that the performance of the catalyst has not been affected by the fault that set this DTC, operate the vehicle within the conditions for running and setting DTC P0420 and verify that DTC P0420 runs and passes. Refer to DTC P0420 .

Does the DTC run and pass?

--

Go to Step 24

Go to DTC P0420

24

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK