GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2006 🢒 Torrent 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 DTC P1779

Circuit Description

Engine torque information is sent to the transmission control module (TCM) by the powertrain control module (PCM) through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the PCM and TCM. A fault in the CAN will not cause DTC P1779 to set by itself. If a CAN fault occurs, other DTCs will set before DTC P1779.

When the PCM sends the TCM a driver requested torque signal that is invalid, DTC P1779 will set. DTC P1779 is a type C DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P1779 Torque Delivered Signal

Conditions for Running the DTC
    • No CAN DTC U0100.
    • The ignition voltage is 10.2-15.5 volts.
    • The ignition has been ON for at least 3 seconds.
    • Trans. Protection Mode is OFF.
    • The engine speed is 400 RPM or greater.

Conditions for Setting the DTC

Engine torque signal is below the lower limit, above the upper limit, or is an unreliable value for 4 seconds.

Action Taken When the DTC Sets
    • The TCM uses 300 N·m (221 lb ft) as a default value for driver requested torque.
    • The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Failure Records.
    • The TCM stores DTC P1779 in TCM history.

Conditions for Clearing the MIL/DTC
    • The TCM clears the DTC from TCM history if the vehicle completes 40  warm-up cycles without an emission-related diagnostic fault occurring.
    • The TCM cancels the DTC default actions when the ignition is OFF long enough in order to power down the TCM.

Step

Action

Yes

No

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.

    3. Important: 

       • Before clearing the DTC, use the scan tool in order to record the PCM Freeze Frame and the TCM Failure Records. Using the Clear Eng./Trans. DTC Info function erases the Freeze Frame and Failure Records from the powertrain control module (PCM) and the transmission control module (TCM).
       • Using the Clear Eng./Trans. DTC Info function erases stored DTCs in both the PCM and TCM.

  3. Record the DTC Failure Records.

Did you record any PCM Failure Records?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

Go to Step 3

3
  1. Clear the DTC.
  2. Turn the ignition OFF for at least 30 seconds.
  3. Start, and allow the engine to idle.

Did DTC P1779 reset?

Go to Step 4

Go to Testing for Intermittent Conditions and Poor Connections

4

Did any other DTCs set?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

Go to Step 5

5

Replace the PCM. Refer to Control Module References for replacement, setup, and programming.

Is the action complete?

Go to Step 6

--

6

Perform the following operation to verify the repair:

  1. Select DTC on the scan tool.
  2. Select Clear Info.
  3. Start, and idle the engine.
  4. Select Specific DTC.
  5. Enter DTC P1779.

Does the DTC reset?

Go to Step 2

Go to Step 7

7

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK