GM Service Manual Online
For 1990-2009 cars only

Step

Action

Values

Yes

No

Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The temperature cannot be adjusted, or the cooling is insufficient during A/C operation.

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Turn ON the ignition, with the engine OFF.
  2. Place the blower motor switch in each speed position.

Does the blower motor operate in any of the speed positions?

--

Go to Step 3

Go to Blower Motor Inoperative

3

Does the blower motor operate at the desired speeds?

--

Go to Step 4

Go to Blower Motor Malfunction

4

When the A/C is ON, does the customer concern occur?

--

Go to Step 5

Go to Step 7

5

  1. Start the engine.
  2. Place the blower motor switch in the maximum speed position.
  3. Place the recirculation switch in the ON position.

Does the recirculation door move to the recirculation position?

--

Go to Step 6

Go to Air Delivery Improper

6

  1. Place the blower motor switch in the maximum speed position.
  2. Place the A/C switch in the ON position.
  3. Place the temperature switch in the coldest position.

Does the A/C compressor operate?

--

Go to Step 7

Go to HVAC Compressor Clutch Does Not Engage

7

Perform the refrigerant system performance test. Refer to Air Conditioning (A/C) System Performance Test .

Did you find and correct the condition?

--

Go to Step 18

Go to Step 8

8

  1. Observe the drive shaft of the air temperature actuator.
  2. Place the air temperature switch from the coldest position to the warmest position.

Does the air temperature actuator drive shaft rotate at all?

--

Go to Step 9

Go to Step 10

9

Inspect the air temperature door and the air temperature actuator for the following conditions:

    • A misaligned air temperature actuator. Refer to Temperature Valve Actuator Replacement .
    • Broken or binding linkages or air temperature door
    • An obstruction that prevents the air temperature door from operating within its full range of motion
    • Missing seals to the air temperature door
    • Misaligned seals to the air temperature door

Did you find and correct the condition?

--

Go to Step 18

Go to Step 10

10

Test the control A and control B circuits of the air temperature actuator for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 18

Go to Step 11

11

  1. Connect a test lamp between the air temperature actuator control A circuit and the control B circuit
  2. Move the air temperature control from hot to cold

Does the test lamp illuminate with each command?

--

Go to Step 14

Go to Step 12

12

Test the ignition 3 voltage circuit of the HVAC control module for the following:

    • An open
    • A high resistance
    • A short to ground

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 18

Go to Step 13

13

Test the ground circuit of the HVAC control module for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 18

Go to Step 15

14

Inspect for poor connections at the harness connector of the air temperature actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 18

Go to Step 16

15

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 18

Go to Step 17

16

Replace the air temperature actuator. Refer to Temperature Valve Actuator Replacement .

Did you complete the replacement?

--

Go to Step 18

--

17

Replace the HVAC control module. Refer to Control Module References for replacement, setup and programming.

Did you complete the replacement?

--

Go to Step 18

--

18

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 2