Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0622: Generator F-Terminal CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0622*, P0625** | P0622*, P0625** | -- | -- |
Field Duty Cycle Signal | P0622*, P0625** | P0622*, P0625** | P0626** | -- |
Turn On Signal | P0621 | -- | P0621 | -- |
* 3.4L (LNJ) engine only ** 3.6L (LY7) engine only | ||||
Typical Scan Tool Data
Circuit | Short to ground | Open | Short to voltage |
|---|---|---|---|
Operating Conditions: Engine Running Parameter Normal Range: 5% to 99% | |||
B+ | 0% | 0% | -- |
Field Duty Cycle Signal | 0% | 0% | 99% |
Circuit/System Description
The engine control module (ECM) uses the generator field duty cycle signal circuit, or F-terminal circuit, to monitor the duty cycle of the generator. The generator field duty cycle signal circuit connects to high side of the field windings in the generator. A pulse width modulated (PWM) high side driver in the voltage regulator turns the field windings ON and OFF. The ECM uses the PWM signal input to determine the generator load on the engine. This allows the ECM to adjust the idle speed to compensate for high electrical loads. The ECM monitors the status of the generator field duty cycle signal circuit. When the key is in the RUN position and the engine is OFF, the ECM should detect a duty cycle near 0 percent. When the engine is running, the duty cycle should be between 5-99 percent.
Conditions for Running the DTC
| • | The engine is running. |
| • | DTC P0621 is not set. |
Conditions for Setting the DTC
The field duty cycle signal is less than 5 percent duty cycle for 30 seconds.
Action Taken When the DTC Sets
| • | The ECM will command the charge indicator to be illuminated on the instrument panel cluster (IPC). |
| • | The driver information center (DIC) will display the SERVICE BATTERY CHARGING SYSTEM message. |
| • | The ECM will not illuminate the malfunction indicator lamp (MIL). |
| • | The ECM will store conditions, which were present when the DTC set as Fail Records data only. |
Conditions for Clearing the DTC
| • | The DTC passes when condition for setting the DTC is no longer present. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
Reference Information
Schematic Reference
Starting and Charging Schematics
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Ignition ON, engine OFF, observe the scan tool ECM GEN-F Terminal Signal parameter. The reading should be less than 5 percent.
- Engine running, observe the scan tool ECM GEN-F Terminal Signal parameter. The reading should be greater than 5 percent.
Circuit/System Testing
- Verify that a test lamp illuminates between the B+ circuit terminal 1 X2 and ground.
- Ignition OFF, disconnect the X1 harness connector at the generator.
- Ignition ON, verify the scan tool ECM GEN-F Terminal Signal is less than 5%.
- Install a 3 A fused jumper wire between the signal circuit terminal 2 X1 and B+. Verify the scan tool ECM GEN-F Terminal Signal is greater than 95%.
- If all circuits test normal, test or replace the generator.
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
| ⇒ | If greater than the specified range, test the signal circuit terminal 2 X1 for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for ECM replacement, setup, and programming. |
