GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2008 🢒 Torrent 🢒 Power and Signal Distribution 🢒 Wiring Systems and Power Management 🢒 DTC P0420 or P0430

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    •  Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0420: Catalyst System Low Efficiency Bank 1

DTC P0430: Catalyst System Low Efficiency Bank 2

Circuit/System Description

In order to maintain a reasonably low emission level of hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx) a 3-way catalytic converter (TWC) is used. The catalyst within the converter promotes a chemical reaction that oxidizes the HC and CO present in the exhaust gas. This reaction converts the gases into harmless water vapor and carbon dioxide. The catalyst also reduces the NOx , converting the NOx into nitrogen. The engine control module (ECM) monitors this process using the post catalyst heated oxygen sensor (HO2S) signal. The post-catalyst HO2S located in the exhaust stream after the TWC, produces an output signal that indicates the oxygen storage capacity of the catalyst. The oxygen storage capacity (OSC) determines the ability of the catalyst to convert the exhaust emissions effectively. If the catalyst is functioning correctly, the post-catalyst HO2S signal will be far less active than the signal produced by the pre-catalyst HO2S.

To determine OSC, the ECM commands a rich air/fuel mixture until all oxygen is removed from the catalyst. The ECM then commands a lean air/fuel mixture and monitors the rear heated oxygen sensors to calculate the oxygen storage capacity. The catalyst is operated in this mode until one of the following conditions occur:

    • The oxygen stored in the catalyst exceeds a calibrated threshold, which is determined from the rear HO2S signal.
    • The rear HO2S indicates the catalyst to be completely saturated with oxygen, which is determined from the rear HO2S signal.

Conditions for Running the DTC
    • Before the ECM can report DTC P0420 or P0430 failed, DTCs P0030, P0031, P0032, P0036, P0037, P0038, P0050, P0051, P0052, P0056, P0057, P0058, P0100, P0101, P0102, P0103, P0121, P0122, P0123, P0131, P0132, P0133, P0135, P0137, P0138, P0140, P0141, P0151, P0152, P0153, P0155, P0157, P0158, P0160, P0161, P0221, P0222, P0223, P0335, P0336, P0338, P2096, P2097, P2098, P2099, P2195, P2196, P2197, P2198, P2232, P2235, P2237, P2240, P2243, P2247, P2251, P2254, P2270, P2271, P2272, P2273, P2297, P2298, P2626, and P2629 must run and pass.
    • DTC P000A, P000B, P000C, P000D, P0010, P0011, P0013, P0014, P0020, P0021, P0023, P0024, P0030, P0031, P0032, P0050, P0051, P0052, P0100, P0101, P0102, P0103, P0116, P0117, P0118, P0119, P0121, P0122, P0123, P0128, P013A, P013C, P013E, P0130, P0131, P0132, P0133, P0135, P0137, P0138, P014A, P0140, P0141, P0150, P0151, P0152, P0153, P0155, P0157, P0158, P0160, P0161, P0221, P0222, P0223, P0300, P0301-P0306, P0443, P0455, P0458, P0459, P0496, P2088, P2089, P2090, P2091, P2092, P2093, P2094, P2095, P2096, P2097, P2098, P2099, P2100, P2101, P2107, P2119, P2122, P2123, P2127, P2128, P2138, P2176, P2177, P2178, P2179, P2180, P2187, P2188, P2189, P2190, P2232, P2235, P2270, P2271, P2272, or P2273 is not set.
    • The engine speed is 1,080-3,000 RPM.
    • The engine load is 13-45 percent.
    • The air flow into the engine is between 4-20 g/s and steady.
    • The ambient air temperature is warmer than -30°C (-22°F).
    • The HO2S 2 is at operating temperature for greater than a range of 140-300 seconds.
    • The Closed Loop fuel control is enabled.
    • The calculated TWC temperature is between 480-750°C (896-1,382°F) and steady.
    • The above conditions exist for approximately 17 minutes.
    • DTC P0420 and P0430 run once a drive cycle. The ECM will attempt to run this diagnostic up to 3 times a drive cycle.

Conditions for Setting the DTC

The ECM determines the oxygen storage capacity (OSC) of the catalyst has degraded below a calibrated threshold.

Action Taken When the DTC Sets

DTCs P0420 and P0430 are Type A DTCs.

Conditions for Clearing the DTC

DTCs P0420 and P0430 are Type A DTCs.

Diagnostic Aids

Inspect for the following conditions, which may cause a catalytic converter to degrade:

    • An engine misfire
    • High engine oil or high coolant consumption
    • Retarded spark timing
    • A weak or poor spark
    • A lean fuel mixture
    • A rich fuel mixture
    • A damaged oxygen sensor or wiring harness

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing
  1. Observe the DTC information with a scan tool. Verify there are no HO2S, or misfire DTCs set.
    2. ⇒If there are any HO2S or misfire DTCs set, diagnosis the applicable DTC before proceeding with this diagnostic procedure. Refer to Diagnostic Trouble Code (DTC) List - Vehicle.
  2. Inspect and verify the following:
    3. • The catalytic converter is an original part
    • The HO2S 2 is secure and the wiring is not damaged, or contacting the exhaust
    • The exhaust system for leaks, damage, or missing hardware
         ⇒If a condition is found, repair as necessary.

    Note: Before replacing the catalytic converter, correct any conditions that may have damaged the converter.

  3. If a condition is not located, replace the catalytic converter.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Catalytic Converter Replacement - Left Side
    •  Catalytic Converter Replacement - Right Side