Circuit Description
DTC C1247 detects a stripped nut or gear assembly during initialization. During the homing sequence, the piston should reach the top of the bore. Then the ABS motor stalls. If the ABS motor does not stall the ABS motor must be spinning with little or no resistance. This indicates a nut/screw or gear malfunction.
Conditions for Setting the DTC
DTC C1247 can only set during initialization. A malfunction exists if the feedback current is less than the command current for a specified period of time.
Action Taken When the DTC Sets
| • | A malfunction DTC stores. |
| • | The ABS/TCS disables. |
| • | The amber ABS/TCS warning indicators turn on. |
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists and the Scan Tool Clear DTC function is used. |
| • | 100 drive cycles pass with no DTC detected. |
Diagnostic Aids
The following conditions may cause an intermittent malfunction if the conditions exist in a mechanical part of the system:
| • | Sticking |
| • | Binding |
| • | Slipping |
Use the enhanced diagnostic function of the Scan Tool in order to measure the frequency of the malfunction. Refer to the Scan Tool manual or Scan Tool Diagnostics located in this section for the procedure. DTC C1247 may set after modulator disassembly if the modulator pistons are positioned at the bottom of the modulator piston bore. If DTC C1247 only occurs once and DTC C1256 also occurs, refer to DTC C1256 Left Front ABS Motor Circuit Open . If intermittent and enhanced diagnostics shows this DTC occurs during ABS, refer to DTC C1256 Left Front ABS Motor Circuit Open .
Depending on the frequency of the malfunction, a physical inspection of the mechanical parts suspected of causing the malfunction may be necessary.
Clear the DTCs after completing the diagnosis. Test drive the vehicle for three drive cycles in order to verify that the DTC does not reset. Use the following procedure in order to complete one drive cycle:
- Start the vehicle.
- Drive the vehicle over 16 km/h (10 mph).
- Stop the vehicle.
- Turn the ignition to the OFF position.
Important: Zero the J 39200 test leads before making any resistance measurements.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Diagnostic System Check performed? | -- | Go to Step 2 | Go to Diagnostic System Check | ||||||||
2 |
Does DTC C1256 also set as a current DTC? | -- | Go to Step 3 | |||||||||
3 |
Are the left front ABS motor command current and the left front ABS motor feedback current within the specified current? | 9-11A | Go to Step 4 | Go to Step 6 | ||||||||
4 |
Have the following conditions been meet?
| 5-7A | Go to Step 5 | Go to Step 6 | ||||||||
5 |
Did the brake pedal rise? | -- | Go to Step 22 | Go to Step 6 | ||||||||
6 |
Is the resistance less than or equal to the specified value? | 1.5ohms | Go to Step 7 | Go to Step 15 | ||||||||
7 | Use the J 39200 in order to measure the resistance between the 6-way ABS brake motor pack connector harness terminal E and the 8-way EBCM/EBTCM connector C2 terminal H. Is the resistance less than or equal to the specified value? | 1.5ohms | Go to Step 8 | Go to Step 16 | ||||||||
8 | Use the J 39200 in order to measure the resistance between the 6-way ABS brake motor pack connector terminal E and the 6-way ABS brake motor pack connector terminal F. Is the resistance less than or equal to the specified value? | 1.5ohms | Go to Step 9 | Go to Step 17 | ||||||||
9 |
(The ABS brake motor pack is the unit with the three small gears. The ABS brake motor pack left front gear is the gear closest to the front when the ABS brake modulator is mounted in the vehicle.) Is the ABS brake motor left front gear stripped? | -- | Go to Step 17 | Go to Step 10 | ||||||||
10 | Inspect for a stripped ABS brake modulator pack left front gear. (The ABS brake modulator unit is the unit with the three large gears. The ABS brake modulator left front gear is the gear closest to the front when the ABS brake modulator is mounted in the vehicle.) Is the ABS brake modulator left front gear stripped? | -- | Go to Step 18 | Go to Step 11 | ||||||||
11 |
(The ABS brake modulator left front gear is the gear closest to the front when the ABS brake modulator is mounted in the vehicle.) Does the ABS brake modulator left front gear set move at least one full revolution in both directions? | -- | Go to Step 12 | Go to Step 17 | ||||||||
12 |
Does the ABS brake modulator left front gear rotate more than 13 full turns from lock to lock? | -- | Go to Step 19 | Go to Step 13 | ||||||||
13 |
Do any of the terminals exhibit poor terminal contact or corrosion? | -- | Go to Step 20 | Go to Step 14 | ||||||||
14 |
Does DTC C1247 set as a current DTC? | -- | Go to Step 21 | Go to Step 22 | ||||||||
15 | Repair the high resistance in CKT 1280. Is the repair complete? | -- | Go to Diagnostic System Check | -- | ||||||||
16 | Repair the high resistance in CKT 1281. Is the repair complete? | -- | Go to Diagnostic System Check | -- | ||||||||
17 | Replace the ABS brake motor pack. Refer to ABS Motor Pack Replacement . Is the repair complete? | -- | Go to Diagnostic System Check | -- | ||||||||
18 | Replace the ABS brake modulator gear. Refer to Brake Modulator Gear Replacement . Is the repair complete? | -- | Go to Diagnostic System Check | -- | ||||||||
19 | Replace the ABS brake modulator. Refer to Brake Modulator Replacement . Is the repair complete? | -- | Go to Diagnostic System Check | -- | ||||||||
20 | Replace the terminals that exhibit signs of poor terminal contact or corrosion. Is the repair complete? | -- | Go to Diagnostic System Check | -- | ||||||||
21 | Replace the EBCM/EBTCM. Refer to Electronic Brake and Traction Control Module Replacement . Is the repair complete? | -- | Go to Diagnostic System Check | -- | ||||||||
22 | The malfunction is intermittent or not present at this time. Is a concern still present? | -- | Go to Diagnostic Aids | Go to Diagnostic System Check |
