GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 39630-2 Lower Control/Valve Body Gasket Guide Pins
    • J 36850 Assembly Lubricant (or equivalent)

    Object Number: 15484  Size: SH
  1. Inspect the accumulator housing for damage or scoring in the bores.
  2. Inspect all fluid passages for debris.

  3. Object Number: 15483  Size: SH
  4. Install new seals (947, 961) onto the accumulator pistons (946, 960).
  5. Install the following parts:
  6. 4.1. The forward accumulator pin (962) into the accumulator housing (944)
    4.2. The forward accumulator piston (960)
    4.3. The spring (963)
  7. Install the following parts:
  8. 5.1. The reverse accumulator pin (948)
    5.2. The reverse accumulator piston (946)
    5.3. The reverse accumulator spring (949)
  9. Install the following parts:
  10. 6.1. The accumulator housing cover gasket (964)
    6.2. The accumulator housing cover (965)

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    6.3. The five 8 mm accumulator housing cover bolts (966)

    Tighten
    Tighten the bolts to 8-14 N·m (6-10 lb ft).


    Object Number: 509718  Size: SH
  11. Install a new seal (969) onto the 1-2 accumulator piston (968).
  12. Install the following parts:
  13. • The 1-2 accumulator spring (973)
    • The 1-2 accumulator pin (970)
    • The 1-2 accumulator piston (968)
    • The snap ring (349). Install the snap ring onto the 1-2 accumulator pin (970) after you have passed the pin through the top of the accumulator housing (944).
    • The 1-2 accumulator inner spring assembly (971)

    Object Number: 509725  Size: SH
  14. Install the following parts:
  15. • The 3-4 accumulator spring (950)
    • The 3-4 accumulator pin (977)
    • The 3-4 accumulator piston (975)
    • The snap ring (349). Install the snap ring onto the 3-4 accumulator pin (977) after you have passed the pin through the top of the accumulator housing (944).

    Object Number: 15486  Size: SH
  16. Install the checkballs (#1-4) into their proper cavities in the accumulator housing (944). Retain the checkballs with J 36850 or equivalent.

  17. Object Number: 1217580  Size: SH
  18. Install the J 39630-2 into the lower control valve body gasket for the accumulator housing. Make sure that the 1-2 accumulator inner spring assembly (971) goes into the channel plate washer side down.
  19. Install the accumulator housing (944) onto the lower channel plate and install the bolts (534, 951, 952, 954) and hand tighten.
  20. Remove the J 39630-2 and install the rest of the accumulator housing bolts, including bolts (534) from the channel plate side.
  21. Tighten
    Tighten the bolts (534, 951, 952, 954) in a star pattern to 8-14 N·m (6-10 lb ft).