Camshaft Actuator System Description. Pontiac Vibe

For 1990-2009 cars only

Makes 🢒 Pontiac 🢒 2009 🢒 Vibe - AWD 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 Camshaft Actuator System Description


(1)	CMP Actuator Assembly
(2)	Intake Camshaft
(3)	Camshaft Position (CMP) Sensor
(4)	Crankshaft Position (CKP) Sensor
(5)	Camshaft Position (CMP) Actuator Solenoid Valve

The camshaft position (CMP) actuator system enables the powertrain control module (PCM) to change camshaft timing while the engine is running. The CMP actuator assembly (1) varies camshaft position in response to directional changes in oil pressure. The CMP actuator solenoid valve controls the oil pressure that is applied to advance or retard the camshaft. Modifying camshaft timing under changing engine demand provides better balance between the following performance concerns:

•	Engine power output

•	Fuel economy

•	Lower tailpipe emissions

The CMP actuator solenoid valve (5) is controlled by the PCM. The crankshaft position (CKP) sensor (4) and the CMP sensor (3) are used to monitor changes in camshaft position. The PCM uses information from the following sensors in order to calculate the desired camshaft position:

•	The engine coolant temperature (ECT) sensor

•	The mass air flow (MAF) sensor

•	The throttle position (TP) sensors

•	The vehicle speed sensor (VSS)

Camshaft Position (CMP) Actuator Assembly


(1)	Lock Pin
(2)	Vane Wheel
(3)	Intake Camshaft
(4)	CMP Actuator Housing

The CMP actuator assembly has an outer housing (4) that is driven by the engine timing chain. Inside the assembly is a wheel (2) with fixed vanes that is attached to the intake camshaft (3). The CMP actuator assembly also contains a lock pin (1) that prevents movement between the outer housing and the wheel vane assembly. The lock pin is released by oil pressure before any movement in the CMP actuator assembly takes place.

Camshaft Position (CMP) Actuator Solenoid Valve


(1)	Spool Valve
(2)	Solenoid Plunger
(3)	Solenoid Coil
(4)	Oil Return During Retard
(5)	Oil Supply
(6)	Oil Return During Advance
(7)	Oil Supply to Camshaft Position Actuator for Advance
(8)	Oil Supply to Camshaft Position Actuator for Retard

The CMP actuator solenoid valve directs the oil flow that controls the camshaft phase movement. The PCM commands the CMP solenoid to move the solenoid plunger (2) and spool valve (1) until oil flows from the advance passage (7) or the retard passage (8). In most operating conditions the opposite oil return passage is open at the same time as the oil supply passage.

Operation

The PCM operates the CMP actuator solenoid valve by pulse width modulation (PWM) of the solenoid coil. The higher the PWM duty cycle, the larger the change in camshaft timing. Oil pressure that is applied to the advance side of the fixed vanes will rotate the camshaft in a clockwise direction. The clockwise movement of the camshaft will advance the timing up to a maximum of 40 degrees. When oil pressure is applied to the return side of the vanes, the camshaft will rotate counterclockwise until returning to 0 degrees.

CMP Actuator System Advance


(1)	Vane Wheel
(2)	CMP Actuator Housing, part of CMP actuator assembly
(3)	Intake Camshaft Gear, part of CMP actuator assembly
(4)	Intake Camshaft
(5)	Advance Side Oil Passage, applying pressure
(6)	CMP Actuator Solenoid Valve
(7)	Retard Side Oil Passage, relieving pressure

Oil flowing to the CMP actuator housing (2) from the CMP solenoid advance passage (5) applies pressure to the advance side of the vane wheel (1) in the CMP actuator assembly. At the same time the CMP solenoid retard passage (7) is open, allowing oil pressure to decrease on the retard side of the vane wheel. These two simultaneous actions cause the vane wheel (1) to rotate clockwise, advancing camshaft advance timing.

CMP Actuator System Retard


(1)	Vane Wheel
(2)	CMP Actuator Housing, part of CMP actuator assembly
(3)	Intake Camshaft Gear, part of CMP actuator assembly
(4)	Intake Camshaft
(5)	Advance Side Oil Passage, relieving pressure
(6)	CMP Actuator Solenoid Valve
(7)	Retard Side Oil Passage, applying pressure

When the oil flowing to the CMP actuator housing (2) is from the CMP solenoid retard passage (7), oil pressure is applied to the retard side of the vane wheel (1). Because the solenoid advance passage (5) is open, allowing oil pressure to decrease on the advance side of the vane wheel (1), the camshaft position retards.

The PCM can also command the CMP actuator solenoid valve to stop oil flow from both passages in order to hold the current camshaft position. The PCM is continuously comparing CMP sensor input with CKP sensor input in order to monitor camshaft position and detect any system malfunctions. The following table provides camshaft phase commands for common driving conditions:

CMP Actuator System Operation

Driving Condition	Change in Camshaft Position	Objective	Result
Engine Warm-up	No Change, Zero Advance	Minimize Valve Overlap	Stabilize Fast Idle Speeds and Improved Fuel Economy
Medium Engine Load	Advance Valve Timing	Increase Valve Overlap	Improved Fuel Economy with Lower Emissions
Low to Medium RPM with Heavy Load	Advance Valve Timing	Advance Intake Valve Closing	Improve Low to Mid-range Torque
High RPM with Heavy Load	Retard Valve Timing	Retard Intake Valve Closing	Improve Engine Output
Idle	No Change, Zero Advance	Minimize Valve Overlap	Stabilize Idle Speed