GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Notice: Check the resistance values of all PCM relays, solenoids, and other output controls before replacing or substituting the Powertrain Control Module (PCM). Check all the sensor wiring and the PCM output control circuits for a short to ground before replacing or substituting the PCM. Perform all circuit repairs or malfunctioning component part replacements before installing a replacement or substitute PCM. This will prevent damage to the replacement or substitute PCM.

Notice: Do not touch the connector pins or soldered components on the circuit board in order to prevent possible electrostatic discharge (ESD) damage to the PCM.

Notice: Turn the ignition OFF when installing or removing the PCM connectors and disconnecting or reconnecting the power to the PCM (battery cable, PCM pigtail, PCM fuse, jumper cables, etc.) in order to prevent internal PCM damage.

Important: Service of the powertrain control module (PCM) consists of a complete replacement of the PCM. There are no serviceable parts, such as programmable read-only memory (PROM) or erasable programmable read-only memory (EPROM) to replace inside the PCM. If the PCM is determined to be faulty, the PCM is to be replaced as a complete assembly.


    Object Number: 856534  Size: SH
  1. Disconnect the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Remove the two retainers from the PCM close out panel (1) below the instrument panel (IP) compartment door.
  3. Swing the PCM close out panel (1) down.

  4. Object Number: 834062  Size: SH
  5. Open the IP compartment.
  6. Push in on both sides of the IP compartment in order to release the safety catches.
  7. Remove the IP compartment door assembly from the IP.

  8. Object Number: 834064  Size: SH
  9. Remove the two PCM bracket fasteners.

  10. Object Number: 856535  Size: SH
  11. Pull the PCM (2) with brackets (3) toward you and swing both down away from under the IP.
  12. Disconnect the four PCM electrical connectors (1).
  13. Remove the four fasteners and the two brackets (3) from the PCM (2).

Installation Procedure

Notice: Do not touch the connector pins or soldered components on the circuit board in order to prevent possible electrostatic discharge (ESD) damage to the PCM.

Notice: Turn the ignition OFF when installing or removing the PCM connectors and disconnecting or reconnecting the power to the PCM (battery cable, PCM pigtail, PCM fuse, jumper cables, etc.) in order to prevent internal PCM damage.


    Object Number: 856535  Size: SH
  1. Install the two PCM brackets (3) to the PCM (2).
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Secure the two brackets to the PCM with the four fasteners.
  4. Tighten
    Tighten the PCM bracket fasteners to 3.2 N·m (28 lb in).

  5. Connect the four PCM electrical connectors (1).
  6. Swing the PCM (2) with bracket (3) up in position under the IP.

  7. Object Number: 834064  Size: SH
  8. Secure the PCM to the IP with the two fasteners.
  9. Tighten
    Tighten the two fasteners to 9 N·m (80 lb in).


    Object Number: 834062  Size: SH
  10. Install the IP compartment door into the IP.
  11. Push in on both sides of the IP compartment in order to release the safety catches and close the door.

  12. Object Number: 856534  Size: SH
  13. Swing the close out panel (1) up under the PCM and secure with the two retainers.
  14. Connect the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  15. Program the vehicle identification number (VIN) to the replacement PCM. Refer to Control Module References in Computer/Integrating Systems.