GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The DTC P0172 Fuel Trim System Rich diagnostic monitors the heated oxygen sensor (HO2S) indications of the air/fuel mixture. In order to provide the best possible combination of driveability, fuel economy, and emission control, the powertrain control module (PCM) uses a Closed Loop air/fuel metering system. The PCM monitors the HO2S signal voltage and when in Closed Loop adjusts fuel delivery based on the HO2S signal voltage. Changes in fuel delivery will be indicated by the long term and the short term fuel trim values that are displayed on the scan tool. The ideal fuel trim value is around 0 percent. The PCM will add fuel when the heated oxygen sensor signal is indicating a lean condition. Additional fuel is indicated by fuel trim values that are above 0 percent. The PCM will reduce the amount of fuel delivered when a rich condition is indicated by the HO2S. Fuel trim values below 0 percent indicate a reduction in fuel. A fuel trim DTC can be set when exhaust emissions reach excessive levels because of a lean or rich condition.

HO2S Indication

Short Term FT Action

Long Term FT Action

Short Term FT Response

Lean Condition

Quick Increase of 1% or More

Slow Increase of 1% or More

Return to 0%

Desired Condition

Stays Near 0%

Stays at Learned +/- Value

Stays Near 0%

Rich Condition

Quick Decrease of -1% or Less

Slow Decrease of -1% or Less

Return to 0%

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0172 Fuel Trim System Rich

Condition for Running the DTC

    • DTC P0010, P0011, P0012, P0031, P0032, P0100, P0101, P0102, P0103, P0115, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0134, P0335, P0339, P0340, P0341, P0500, P2195, P2196, P2238, P2239, P2252, P2253, P2A00 are not set.
    • The engine coolant temperature (ECT) is more than 70°C (158°F).
    • The engine is running at steady speed.
    • The engine is operating in Closed Loop.
    • DTC P0172 runs continuously once the above condition is met.

Conditions for Setting the DTC

The average fuel trim value is -35 percent or more, for at least 9 seconds. Average fuel trim is short term fuel trim plus long term fuel trim.

Action Taken When the DTC Sets

    • The PCM illuminates the malfunction indicator lamp (MIL) after 2 consecutive ignition cycles in which the diagnostic runs with the fault active.
    • The PCM stores the conditions which were present when the DTC set as Freeze Frame data.

Conditions for Clearing the MIL/DTC

    • The PCM turns OFF the MIL on the third consecutive trip cycle during which the diagnostic has been run and the fault condition is no longer present.
    • A DTC will clear after 40 consecutive warm-up cycles have occurred without a fault.
    • A DTC can be cleared by using the scan tool Clear DTC Information function.

Diagnostic Aids

Check for any of the following conditions:

    • Check for a restriction in the inlet air passage. A duct or inlet hose that collapses when hot or that is blocked by debris can cause a DTC P0172 to set.
    • Check for the correct fuel pressure. The fuel system will be rich if the fuel pressure is too high. In order to determine the cause of a DTC P0172 monitoring the fuel pressure while driving the vehicle at various road speeds may be necessary. Refer to Fuel System Diagnosis .
    • Check for fuel contamination of the crankcase. Fuel that has entered the crankcase can release vapors that enter the engine through the positive crankcase ventilation (PCV) system, thereby causing a rich running condition.
    • Check for a contaminated oxygen sensor. Silicone and other contaminants can cause the oxygen sensor to provide false exhaust oxygen content readings. If contamination is found, determine the cause and correct the condition before replacing the HO2S.
    • Inspect the HO2S 1 for water intrusion into the wiring harness and the sensor housing. Water can create a short to voltage in the HO2S signal circuit causing a false rich indication.
    • Check the HO2S 1 and the manifold absolute pressure (MAP) sensor for a faulty electrical connection to the PCM.

An intermittent malfunction may be caused by a fault in the HO2S 1 electrical circuit. Inspect the wiring harness and the components for an intermittent condition. Refer to Intermittent Conditions .

Repair any electrical circuit faults that were found. Refer to Wiring Repairs .

If a DTC P0172 cannot be duplicated, the information included in the Freeze Frame data can be useful in determining vehicle operating conditions when the DTC was first set.

Test Description

The numbers below refer to the step numbers in the diagnostic table.

  1. The Diagnostic System Check - Vehicle prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool, if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.

  2. A plugged air filter can cause a rich condition and set a DTC P0172.

  3. Engine control sensors that are found to be out range (skewed) or fixed, can cause the engine to run rich. Inspect the performance of the MAF sensor. Inspect for air restrictions and air inlet leaks near the MAF sensor. If the HO2S voltage is fixed low, while the fuel trim is constantly high, check the MAF sensor circuits for resistance. High circuit resistance can cause the sensor to read the incorrect volume of air, resulting in the wrong fueling condition. Refer to the applicable sensor DTC table for direction in diagnosing any possible sensor error.

  4. Operating the vehicle in Check Mode enhances the diagnostic capabilities of the PCM. The catalytic converter diagnostic can be monitored on the scan tool under the I/M System Information selection. When the Catalyst test displays a YES status, indicating that the catalytic converter system diagnostic is completed, check for DTC P0420 in the Last Test Failed screen of the scan tool. If there is no DTC P0420 displayed, the catalytic converter diagnostic has run and passed, indicating that no malfunction was present this time. The DTCs MUST be cleared in order to view the Current Status of the system diagnostics being performed. Do not forget that the I/M System Information tests only indicate that the test has run, not whether the test passed or failed. The Last Test Failed screen must be checked for related DTCs in order to determine the outcome of the diagnostic test involved.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Start the engine.
  2. Operate the vehicle until the loop status indicates Closed Loop.
  3. Observe the Short Term FT parameter display on the scan tool.

Is the Short Term FT parameter displayed on the scan tool more than the specified value?

-20 %

Go to Diagnostic Aids

Go to Step 3

3

Visually and physically check the air filter and the air induction assembly for any of the following conditions:

    • A dirty or contaminated air filter
    • Any restrictions or blockage of the air flow
    • Any leaks in the exhaust system

Did any of the above inspections isolate a condition requiring a repair?

--

Go to Step 9

Go to Step 4

4

  1. Start the engine.
  2. Run the engine until the engine reaches a normal operating temperature.
  3. Observe the operation of the following sensors at idle, with a scan tool:
  4. • The mass air flow (MAF) sensor
    • The engine coolant temperature (ECT) sensor
    • The fuel control heated oxygen sensor (HO2S 1)
  5. Compare the observed sensor readings with the Typical Scan Tool Data Values located in the engine scan tool data list. Refer to Scan Tool Data List .
  6. Inspect any errant readings for their cause and repair as necessary.

Was a repair necessary?

--

Go to Step 9

Go to Step 5

5

  1. Turn OFF the ignition.
  2. Install a fuel pressure gage. Refer to Fuel Pressure Gage Installation and Removal .
  3. Observe the fuel pressure with the engine running at a normal operating temperature.

Is the fuel pressure within the specified range?

301-347 kPa (44-50 psi)

Go to Step 6

Go to Fuel System Diagnosis

6

  1. Check the evaporative emission (EVAP) control system for possible over-purging of the EVAP system. Refer to Evaporative Emission Control System Diagnosis .
  2. Repair as necessary.

Was a problem found?

--

Go to Step 9

Go to Step 7

7

  1. Remove and visually and physically inspect the HO2S 1 for silicon contamination. Contamination will be indicated by a powdery white deposit on the portion of the HO2S that is exposed to the exhaust stream.
  2. If contamination is evident on the HO2S, replace the contaminated sensor and correct the source of contamination. Refer to Heated Oxygen Sensor 1 Replacement .

Did the sensor require replacement?

--

Go to Step 9

Go to Step 8

8

Is a rich condition still present?

--

Go to Symptoms - Engine Controls

Go to Step 9

9

  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.

Does the DTC run and pass?

--

Go to Step 10

Go to Step 2

10

  1. In order to ensure that the performance of the catalyst has not been affected by the fault that set this DTC, place the vehicle in Check Mode. Refer to Service Bay Test .
  2. While in check mode, operate the vehicle within the conditions for running and setting DTC P0420 and verify that DTC P0420 runs and passes. Refer to DTC P0420 .

Does DTC P0420 run and pass?

--

Go to Step 11

Go to DTC P0420

11

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK