The numbers below refer to the step numbers on the diagnostic table.
Step
| Action
| Values
| Yes
| No
|
1
| Did you perform the Diagnostic System Check - Vehicle?
| --
| Go to
Step 2
| Go to
Diagnostic System Check - Vehicle
in
Vehicle DTC information
|
2
| Was the Fuel Injector Coil Test Procedure performed?
| --
| Go to
Step 3
| Go to
Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Between 10-35 Degrees C (50-95 Degrees F)
|
3
| Is the engine coolant temperature more than the specified value?
| 94°C (201°F)
| Go to
Step 4
| Go to
Step 5
|
4
| Allow the engine to cool to less than the specified value.
Is the engine coolant temperature less than the specified value?
| 94°C (201°F)
| Go to
Step 5
| --
|
5
|
Caution: Wrap a shop towel around the fuel pressure connection in order to reduce
the risk of fire and personal injury. The towel will absorb any fuel leakage
that occurs during the connection of the fuel pressure gage. Place the towel
in an approved container when the connection of the fuel pressure gage
is complete.
- Install the fuel pressure gage. Refer to
Fuel Pressure Gage Installation and Removal
.
- Energize the fuel pump by using the scan tool.
- Place the bleed hose of the fuel pressure gage into an approved gasoline
container.
- Bleed the air out of the fuel pressure gage.
- Observe the reading on the fuel pressure gage.
Is the fuel pressure within the specified range?
| 301-347 kPa
(44-50 psi)
| Go to
Step 6
| Go to
Fuel System Diagnosis
|
6
| Turn the fuel pump OFF.
Does the fuel pressure remain constant?
| --
| Go to
Step 7
| Go to
Fuel System Diagnosis
|
7
|
- Use 2 jumper wires from the
J 35616
Connector Test Adapter Kit in order to connect the fuel injector
to the
J 39021
Fuel Injector Tester
test leads.
- Connect the
J 39021
to
B+ and to ground.
- Set the amperage supply selector switch on the fuel injector tester to
the Balance Test 0.5-2.5 amp position.
- Energize the fuel pump by using the scan tool.
- Record the fuel pressure indicated by the fuel pressure gage after the
fuel pressure stabilizes. This is the 1st pressure reading.
- Energize the fuel injector by depressing the Push to Start Test button
on the fuel injector tester.
- Record the fuel pressure indicated by the fuel pressure gage after the
fuel pressure gage needle has stopped moving. This is the 2nd pressure reading.
- Repeat step 1 through step 6 for each fuel injector.
- Subtract the 2nd pressure reading from the 1st pressure reading for one
fuel injector. The result is the pressure drop value.
- Obtain a pressure drop value for each fuel injector.
- Add all of the individual pressure drop values. This is the total pressure
drop.
- Divide the total pressure drop by the number of fuel injectors. This is
the average pressure drop.
Does any fuel injector have a pressure drop value that is higher or lower than
the average pressure drop by the specified value?
| 10 kPa (1.5 psi)
| Go to
Step 8
| Go to
Symptoms - Engine Controls
|
8
|
Notice: Do not repeat any portion of this test before running the engine in
order to prevent the engine from flooding.
Re-test any fuel injector that does not meet the specification. Refer to the
procedure in step 7.
Does any fuel injector still have a pressure drop value that is either higher
or lower than the average pressure drop by the specified value?
| 10 kPa (1.5 psi)
| Go to
Step 9
| Go to
Symptoms - Engine Controls
|
9
| Replace the fuel injectors. Refer to
Fuel Injector Replacement
.
Did you complete the replacement?
| --
| Go to
Step 10
| --
|
10
| Does an engine performance concern still exist?
| --
| Go to
Symptoms - Engine Controls
| System OK
|
