GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2007 🢒 Vibe - FWD 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 Rough, Unstable, or Incorrect Idle and Stalling

Rough, Unstable, or Incorrect Idle, Stalling

Checks

Action

DEFINITION: The engine runs unevenly at idle. If severe, the engine or vehicle may shake. The engine idle speed may vary in RPM. Either condition may stall the engine. The engine idles at an incorrect speed.

Preliminary Check
    • Refer to Diagnostic System Check - Vehicle .
    • Refer to Symptoms - Engine Controls .

Sensor Checks
    • Inspect the heated oxygen sensors (HO2S) 1 and HO2S 2 for a condition that can affect sensor activity and response. Refer to Diagnostic Aids in DTC P2195 .
    • Inspect the throttle position (TP) sensor. A sticking throttle shaft or a binding throttle linkage will causes a high TP sensor voltage. Under these conditions the powertrain control module (PCM) may not control the idle. Monitor the TP sensor angle with the scan tool. The indicated angle should be approximately 9-14 percent with the throttle closed.
    • Check the accelerator pedal position (APP) sensor. First observe the APP sensor 1 voltage with the scan tool. The indicated voltage should be approximately 0.5-1.1 volts with the throttle closed. Next check the APP sensor 2 voltage with the scan tool. The indicated voltage should be approximately 1.2-2 volts with the throttle closed.
    • Inspect the engine coolant temperature (ECT) sensor. A fixed or inaccurate ECT sensor reading can cause the engine idle to surge or race. Using the scan tool, compare the ECT with the ambient air temperature on a cold engine. If the engine coolant is 5°C (9°F) more than or 5°C (9°F) less than the ambient air temperature, inspect the resistance of the coolant sensor. Refer to Temperature Versus Resistance . If the ECT is significantly less than the ambient air temperature, inspect the coolant sensor electrical circuit for high resistance.
    • Inspect the mass air flow (MAF) sensor operation. Run the engine to normal operating temperature. Turn OFF all accessories and observe the MAF sensor at idle with a scan tool. If the MAF sensor reading is more than 3.5 g/s refer to DTC P0101 . If the MAF sensor reading is less than 1.0 g/s, inspect for a vacuum leak between the MAF sensor and the engine.

Fuel System Checks
    • Inspect the operation of the fuel system for rich or lean condition. Operate the vehicle under the conditions that caused the concern. Monitor the Fuel Trim parameter on a scan tool in order to identify the problem.
       - Lean--The Long Term Fuel Trim will be more than 20 percent. Refer to Diagnostic Aids in DTC P0171 .
       - Rich--The Long Term Fuel Trim will be less than -20 percent. Refer to Diagnostic Aids in DTC P0172 .
    • Test the fuel pressure while the condition exists. Refer to Fuel System Diagnosis .
    • Inspect the evaporative emission (EVAP) control system. Refer to Evaporative Emission Control System Diagnosis .

Ignition System Checks
    • Test for the proper secondary voltage output with a J 26792 Spark Tester.
    • Inspect the spark plugs for correct operation and good ignition system performance. Refer to Spark Plug Inspection .
    • Inspect the ignition coil boots for damage.

Engine Mechanical Check
    • Inspect for the following engine mechanical conditions:
       - Faulty hydraulic lifter assemblies
       - Broken or weak valve springs
       - Low compression
       - Incorrect valve timing
       - Sticking or leaking valves
       - Incorrect or worn camshaft
    • Refer to the Symptoms - Engine Mechanical .

Additional Checks
    • Inspect for vacuum leaks. Vacuum leaks can cause a higher than normal idle speed.
    • Verify the PCM grounds are clean, tight, and in the proper locations. Refer to Engine Controls Schematics .
    • Check the scan tool A/C Request Signal parameter to determine if the PCM is receiving an A/C signal. The idle speed should be increased when the A/C compressure clutch is engaged.
    • Inspect the battery cables and the ground straps. They should be clean and secure.
    • Inspect the A/C refrigerant pressure for being too high or for a faulty high pressure switch. Refer to Diagnostic Starting Point - Heating, Ventilation and Air Conditioning .
    • The engine will run rough and the engine can stall if the camshaft position (CMP) actuator solenoid is advancing camshaft timing at idle. Inspect for a fully energized or stuck CMP actuator solenoid. If the operation of the CMP actuator solenoid is suspect, refer to DTC P0012 .
    • Inspect the positive crankcase ventilation (PCV) valve for correct operation and the correct part. Refer to Crankcase Ventilation System Inspection/Diagnosis .
    • Check the vacuum lines and hoses for leaks or incorrect routing. Refer to Emission Hose Routing Diagram and Evaporative Emissions Hose Routing Diagram .
    • Inspect that the idle speed is increasing for changes in electrical loads on the engine. Verify on the scan tool with the High Electrical Load parameter.
    • Verify that the PCM is increasing the idle speed when the P/S system pressure is increased on turns. Verify on the scan tool with the Power Steering Switch parameter.
    • Inspect for broken or worn motor and transmission mounts.