GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The heated oxygen sensor (HO2S) 1 is a wide band or wide range design. As with all oxygen sensors, the wide band HO2S measures the amount of oxygen in the exhaust system, but provides more information than the typical switching style HO2S. The wide band sensor consists of an oxygen sensing cell, an oxygen pumping cell, and a heater. The exhaust gas sample passes through a diffusion gap between the sensing cell and the pumping cell. The powertrain control module (PCM) supplies a voltage to the HO2S and uses this voltage as a reference to the amount of oxygen in the exhaust system. An electronic circuit within the PCM controls the pump current through the oxygen pumping cell in order to maintain a constant voltage in the oxygen sensing cell. The PCM monitors the voltage variation in the sensing cell and attempts to keep the voltage constant by increasing or decreasing the amount of current flow, or oxygen ion flow, to the pumping cell. By measuring the amount of current required to maintain the voltage in the sensing cell, the PCM can determine the concentration of oxygen in the exhaust. The HO2S input signal is displayed as a voltage within the range of 1-5 volts, with a steady value of 3.2-3.3 volts equal to the air fuel ratio of 14.7:1. If the HO2S 1 input voltage is lower than the specified reference voltage, the PCM determines that the air/fuel ratio is richer than the theoretical air/fuel ratio and reduces the fuel. If the input voltage from the HO2S 1 is higher than the specified reference voltage, the PCM determines that the air/fuel ratio is leaner and increases the fuel. By repeating these operations, the PCM can adjust the air/fuel ratio in order to be closer to the theoretical air/fuel ratio. Control of the fuel delivery system as just described is known as Closed Loop operation.

The DTC P2196 diagnostic monitors the input circuit of the HO2S 1. The PCM determines from the sensor voltage whether the engine requires more or less fuel. If the input voltage indicates that there is a rich condition, DTC P2196 will set

Air Fuel Mixture

Exhaust O2 Content

HO2S 1 Output

Fuel System Response

Lean Mixture

High Oxygen

More Than 3.4 V

Rich Command

Rich Mixture

Low Oxygen

Less Than 3.2 V

Lean Command

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P2196 Heated Oxygen Sensor (HO2S) Signal Biased Rich Sensor 1

Conditions for Running the DTC

    • DTCs P0031, P0032, P0051, P0052, P0100, P0101, P0102, P0103, P0110, P0112, P0113, P0115, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0171, P0172, P0220, P0222, P0223, P0300, P0301-P0304, P0335, P0340, P0341, P0385, P0441, P0455, P0456, P0500, P2135, P2238, P2239, P2252, P2253 are not set.
    • The engine has been running more than 30 seconds.
    • The engine is operating in Closed Loop.
    • The HO2S 2 voltage is less than 0.85 volt.
    • DTC P2196 runs continuously when the above conditions have been met.

Conditions for Setting the DTC

The HO2S 1 input voltage is less than 2.8 volts for at least 2 seconds.

Action Taken When the DTC Sets

    • The PCM illuminates the malfunction indicator lamp (MIL) after 2 consecutive ignition cycles in which the diagnostic runs with the fault active.
    • The PCM records the operating conditions at the time the diagnostic fails. This information is stored in the Freeze Frame buffer.

Conditions for Clearing the MIL/DTC

    • The PCM turns OFF the MIL after 3 consecutive trips without a fault.
    • The PCM clears a History DTC after 40 consecutive warm-up cycles without a fault.
    • Use the scan tool Clear DTC Information function.

Diagnostic Aids

    • The scan tool output control feature, Fuel Injector Modification, can be used at idle to check the oxygen sensor performance. Commanding the Fuel Injector Modification Commanded State to 25 percent should cause the HO2S 1 voltage to decrease to less than 3V. Changing the Fuel Injector Modification Commanded State to -12 percent should cause the HO2S 1 voltage to increase to more than 3.35V. An oxygen sensor that fails to respond accordingly may be faulty or contaminated. When performing the Fuel Injector Modification with the scan tool, the Loop Status will remain Open Loop and the Short Term FT will be fixed at 0 percent.
    • Inspect for a contaminated HO2S. Silicon contamination of the HO2S can cause a low signal voltage to be indicated. Silicon contamination is indicated by a powdery white deposit on the portion of the HO2S exposed to the exhaust stream. Before replacing the HO2S determine the cause of the contamination and correct the condition.
    • Verify the PCM to engine electrical grounds are OK.
    • An incorrect fuel pressure--The fuel system can go rich if the fuel pressure is too high and DTC P2196 may be set. Refer to Fuel System Diagnosis .
    • Fuel contamination--Small amounts of water can be delivered to the fuel injectors and cause a lean exhaust indication. A lean exhaust indication can also be caused by too much alcohol in the fuel. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • An incorrectly calibrated fuel injector. Refer to Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Between 10-35 Degrees C (50-95 Degrees F) and Fuel Injector Balance Test with Special Tool .
    • Inspect for correct operation of the crankcase ventilation system.
    • An evaporative emission (EVAP) system condition--A saturated EVAP canister or faulty operation of the EVAP canister purge solenoid can set a DTC P2196. Refer to Evaporative Emission Control System Diagnosis .
    • An intermittent malfunction may be caused by fault in the HO2S 1 electrical circuit. Inspect the wiring harness and components for any intermittent conditions. Refer to Intermittent Conditions .

The information included in the Freeze Frame data can be useful in determining the vehicle operating conditions when the DTC first set.

Test Description

The numbers below refer to the step numbers in the diagnostic table.

  1. The Diagnostic System Check - Vehicle prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool, if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.

  2. This step checks whether the malfunction that caused the DTC P2196 is still present. Operating the vehicle in Check Mode enhances the diagnostic capabilities of the PCM. The HO2S 1 diagnostic can be monitored on the scan tool under the I/M System Information. When the HO2S test displays a YES status, indicating that the heated oxygen sensor system diagnostic is completed, check for a DTC P2196 in the Last Test Failed screen of the scan tool. If there is no DTC P2196 displayed the HO2S diagnostic has run and passed, indicating that no malfunction was present this time. The DTCs MUST be cleared in order to view the Current Status of the system diagnostics being performed. Do not forget that the I/M System Information tests only indicate that the test has run, not whether the test passed or failed. The Last Test Failed screen must be checked for related DTCs in order to determine the outcome of the diagnostic test involved.

  3. Operating the vehicle in Check Mode enhances the diagnostic capabilities of the PCM. The catalytic converter diagnostic can be monitored on the scan tool under the I/M System Information selection. When the Catalyst test displays a YES status, indicating that the catalytic converter system diagnostic is completed, check for DTC P0420 in the Last Test Failed screen of the scan tool. If there is no DTC P0420 displayed, the catalytic converter diagnostic has run and passed, indicating that no malfunction was present this time. The DTCs MUST be cleared in order to view the Current Status of the system diagnostics being performed. Do not forget that the I/M System Information tests only indicate that the test has run, not whether the test passed or failed. The Last Test Failed screen must be checked for related DTCs in order to determine the outcome of the diagnostic test involved.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Perform the scan tool Clear DTC Information function.
  2. Place the vehicle into Check mode, using the scan tool. Refer to Service Bay Test .
  3. Operate the vehicle within the Freeze Frame conditions as specified, or until the HO2S/O2S test is complete. Refer to the supporting text.

Did DTC P2196 set?

--

Go to Step 3

Go to Diagnostic Aids

3

  1. Visually and physically inspect for the following items:
  2. • The heated oxygen sensor (HO2S) 1 is securely installed.
    • Any corrosion on terminals
    • The proper terminal tension at the HO2S 1 and at the powertrain control module (PCM)
    • Any damaged wiring
  3. Repair as necessary.

Was a repair necessary?

--

Go to Step 11

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the HO2S 1 connector.
  3. Measure the resistance of the HO2S 1, between the heater control and the ignition voltage circuits, with a DMM.

Is the resistance of the sensor within the specified range?

1.2-3.4 ohms at 20°C (68°F)

Go to Step 5

Go to Step 9

5

  1. Turn ON the ignition, with the engine OFF.
  2. Connect a DMM to the HO2S 1 input circuit on the engine harness side and ground.
  3. Measure the HO2S 1 input circuit voltage.

Is the voltage within the specified value?

3.4-3.5 V

Go to Step 6

Go to Step 7

6

  1. Turn ON the ignition, with the engine OFF.
  2. Connect a DMM to the HO2S 1 low reference circuit on the engine harness side and ground.
  3. Measure the HO2S 1 low reference circuit voltage.

Is the voltage within the specified value?

2.9-3.1 V

Go to Step 9

Go to Step 8

7

  1. Test for an open or a short in the HO2S 1 input circuit between the HO2S 1 and the PCM connector.
  2. Repair as necessary. Refer to Wiring Repairs .

Did you find and correct a condition?

--

Go to Step 11

Go to Step 10

8

  1. Test for an open or a short in the HO2S 1 low reference circuit between the HO2S 1 and the PCM connector.
  2. Repair as necessary. Refer to Wiring Repairs .

Did you find and correct a condition?

--

Go to Step 11

Go to Step 10

9

Replace the HO2S 1. Refer to Heated Oxygen Sensor 1 Replacement .

Did you complete the replacement?

--

Go to Step 11

--

10

Replace the PCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 11

--

11

  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC or until the HO2S/O2S test is complete. Review the supporting text.

Did the DTC run and pass?

--

Go to Step 12

Go to Step 2

12

  1. In order to ensure that the performance of the catalyst has not been affected by the fault that set this DTC, place the vehicle in Check Mode. Refer to Service Bay Test .
  2. While in Check Mode, operate the vehicle within the conditions for running and setting DTC P0420 and verify that DTC P0420 runs and passes. Refer to DTC P0420 .

Does DTC P0420 run and pass?

--

Go to Step 13

Go to DTC P0420

13

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK