DEFINITION: This diagnostic table is designed to diagnose ONLY the components of the HYDRAULIC brake system in order to determine if the Hydraulic brake system is operating properly. You will be directed by the appropriate Symptom Table to go to other brake system diagnostic tables as appropriate.

Were you sent here from a Brake Symptom Table?

Go to Step 2

Go to Diagnostic Starting Point - Hydraulic Brakes

Inspect and adjust the brake fluid level in the brake master cylinder. Refer to Master Cylinder Reservoir Filling .

Was the brake fluid level low?

Go to Step 3

Go to Step 4

1. Inspect the brake fluid for the following conditions which indicate brake fluid contamination:

•	Fluid separation indicates two types of fluid are present.

-	A swirled appearance indicates an oil-based substance

-	A layered appearance indicates a silicone-based substance

•	Fluid discoloration

-	A cloudy appearance indicates moisture

-	A dark appearance or suspended particles in the fluid indicates dirt, rust, corrosion, or brake dust

2. Inspect the master cylinder reservoir cap diaphragm and the reservoir-to-master cylinder grommets for swelling. Swelling indicates fluid contamination.

Do any of the above conditions exist?

Go to Step 5

Go to Step 6

1. Inspect the brake fluid for the following conditions which indicate brake fluid contamination:

•	Fluid separation indicates two types of fluid are present.

-	A swirled appearance indicates an oil-based substance

-	A layered appearance indicates a silicone-based substance

•	Fluid discoloration

-	A cloudy appearance indicates moisture

-	A dark appearance or suspended particles in the fluid indicates dirt, rust, corrosion, or brake dust

2. Inspect the master cylinder reservoir cap diaphragm and the reservoir-to-master cylinder grommets for swelling. Swelling indicates fluid contamination.

Do any of the above conditions exist?

Go to Step 5

Go to Step 12

1. Flush the hydraulic brake system. Refer to Hydraulic Brake System Flushing .
2. If the brake fluid WAS contaminated with an oil-based or a silicone-based fluid, complete the following steps and refer to the following procedures:

2.1.	Remove ALL of the brake system components that utilize rubber seals or linings.

2.2.	Clean out the hydraulic brake pipes and the reservoir using denatured alcohol, or equivalent.

2.3.	Dry the brake pipes and the reservoir using non-lubricated, filtered air.

2.4.	Refer to the following procedures in order to repair or replace all of the components that utilize rubber seals or linings:

•	Master Cylinder Reservoir Replacement if necessary

•	Master Cylinder Overhaul or Master Cylinder Replacement

•	Replace the brake master cylinder reservoir cap diaphragm.

•	Front Brake Hose Replacement

•	Rear Brake Hose Replacement

•	Front Brake Caliper Overhaul or Front Brake Caliper Replacement

•	Wheel Cylinder Replacement , if equipped

•	Brake Proportion Valve Replacement if necessary

•	Brake Pressure Modulator Valve Assembly Replacement , if equipped

3. If the brake fluid was NOT contaminated with an oil-based fluid, but WAS contaminated with moisture, dirt, rust, corrosion, or brake dust, replace the brake master cylinder reservoir cap diaphragm. The diaphragm may have allowed moisture or dirt to enter the system.
4. Refill and bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding .

Did you complete the operation and any required repairs and/or replacements?

Go to Step 9

--

1. Inspect the following hydraulic brake system components for external fluid leaks. Repair or replace any of the components found to be leaking brake fluid. Refer to the appropriate procedures:

•	Master Cylinder Overhaul or Master Cylinder Replacement

•	Brake master cylinder reservoir cap diaphragm

•	Front Brake Hose Replacement

•	Rear Brake Hose Replacement

•	Brake Pipe Replacement

•	Front Brake Caliper Overhaul or Front Brake Caliper Replacement

•	Wheel Cylinder Replacement .

•	Brake Proportion Valve Replacement if necessary

•	Brake Pressure Modulator Valve Assembly Replacement , if equipped

2. If you repaired or replaced any of the brake system components listed, bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding . While bleeding the hydraulic brake system, observe for the following conditions:

•	The presence of air in the system at a bleeder valve location other than at the repair location, except if the brake master cylinder was replaced

•	An unrestricted and even flow of brake fluid per axle during the bleeding procedure

Did you find and correct a condition?

Go to Step 7

Go to Step 12

Was air in the system at a bleeder valve location other than at the repair location, except if the brake master cylinder was replaced?

Go to Step 19

Go to Step 8

Was the flow of brake fluid unrestricted and even per axle during the bleeding procedure?

Go to Step 9

Go to Step 10

Inspect the hydraulic function of the brake calipers and the wheel cylinders, for proper operation. Refer to Hydraulic Brake Component Operation Visual Inspection .

Do the brake calipers and the wheel cylinders operate properly?

Go to Step 21

Go to Step 14

Was the flow of brake fluid restricted or uneven through front axle hydraulic components during the bleeding procedure?

Go to Step 13

Go to Step 11

Was the flow of brake fluid restricted or uneven through rear axle hydraulic components during the bleeding procedure?

Go to Step 17

--

Inspect the hydraulic function of the brake calipers and the wheel cylinders for proper operation. Refer to Hydraulic Brake Component Operation Visual Inspection .

Do the brake calipers and the wheel cylinders operate properly?

Go to Step 15

Go to Step 13

Use the following procedure in order to determine if the brake caliper is restricting the flow of brake fluid and/or not operating properly:

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .
3. Open the suspected caliper bleeder valve.
4. Using a large C-clamp, compress the caliper piston and observe for an unrestricted flow of brake fluid and for free movement of the caliper piston.
5. Close the caliper bleeder valve.

Was the flow of brake fluid unrestricted and did the caliper piston move freely?

Go to Step 17

Go to Step 14

Repair or replace any brake caliper or wheel cylinder, if equipped, that was not operating properly. Refer to the appropriate procedure:

Did you complete the repair and/or replacement?

Go to Step 21

--

Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding . Observe the condition and the flow of the brake fluid.

Was air in the system?

Go to Step 19

Go to Step 16

Was the flow of brake fluid unrestricted and even per axle during the bleeding procedure?

Go to Step 21

Go to Step 17

1. Inspect the brake pipes and flexible brake hoses for signs of a fluid restriction; such as being bent, kinked, pinched or damaged. Refer to Brake Pipe and Hose Inspection .
2. Replace any of the hydraulic brake pipes and/or flexible brake hoses found to be bent, kinked, pinched or damaged. Refer to the following procedures as necessary:

•	Front Brake Hose Replacement

•	Rear Brake Hose Replacement

•	Brake Pipe Replacement

3. If none of the hydraulic brake pipes or flexible brake hoses were visibly bent, kinked, pinched or damaged, replace the hydraulic brake flex hose at the restricted location.

Did you find and correct a condition?

Go to Step 21

Go to Step 18

Replace the proportioning valve. Refer to Brake Proportion Valve Replacement .

Did you complete the replacement?

Go to Step 21

--

1. Inspect the hydraulic brake system components for brake fluid seepage at a seal and/or fitting location, which may have drawn air into the system.
2. Inspect the hydraulic brake system components for evidence of a recent repair, which may have introduced air into the system.
3. Repair or replace any of the components found to be installed incorrectly or seeping brake fluid.

Did you find and correct a condition?

Go to Step 21

Go to Step 20

1. Inspect the brake master cylinder for internal fluid leaks. Refer to Brake System Internal Leak Test .
2. Repair or replace the brake master cylinder if it is found to be leaking brake fluid internally. Refer to Master Cylinder Overhaul or Master Cylinder Replacement .

Did you find and correct a condition?

Go to Step 21

Return to Symptom Table

Install or connect components that were removed or disconnected during diagnosis.

Did you complete the operation?

Hydraulic Brake System OK

Return to Symptom Table

--