GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2005 🢒 Wave 🢒 Transmission/Transaxle 🢒 Automatic Transmission - Aisin (81-40LE) 🢒 DTC P0713

DTC P0713 Non European or N. American Emissions

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0713 Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage

Conditions for Setting the DTC
    • The transmission control module (TCM) detects that the analog-to-digital (A/D) value of transmission fluid temperature (TFT) sensor signal is less than 15 and the minimum A/D value is more than 943, when it is past 15 minutes after ignition ON -- A/D value 943:4.7 volts.
    • After one occurrence of above detection
    • Gear selector position is except park and neutral
    • Engine revolution is 400 RPM or greater

Action Taken When the DTC Sets
    • The TCM will request the illumination of the hold lamp and store the DTC when the TCM detects a failure on the first ignition cycle.
    • The TCM judges the temperature of the transmission fluid is 200°C (392°F).
    • No lockup control
    • No 4th gear
    • No self-learning control
    • No timing solenoid control N-D

Conditions for Clearing the DTC
    • The TCM turns OFF the hold lamp when no further failures are detected on the next ignition cycle.
    • The scan tool can clear the DTC from the TCM history.
    • The TCM clears the DTC from the TCM history memory after 40 consecutive ignition cycles without fault.
    • The TCM detects the temperature of the transmission fluid is between 0-150°C for 10 seconds continuously.

Cause of Failure
    • The wiring harness or connector between the TFT sensor and the TCM
    • The TFT sensor
    • The TCM

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check - Automatic Transmission?

--

Go to Step 2

Go to Diagnostic System Check - Automatic Transmission

2
  1. Turn OFF the ignition.
  2. Install the scan tool.
  3. With the engine OFF, turn the ignition switch to the ON position.
  4. Select Store Freeze Frame/Failure Records from the DTC Information menu.
  5. Store Freeze Frame/Failure Records.
  6. Select Clear DTC Information from the DTC Information menu.
  7. Clear the DTC information.
  8. Perform 2 vehicle drive cycles.

Is the hold lamp ON?

--

Go to Step 3

Go to Step 5

3
  1. Select Request DTC by Status from the DTC Information menu.
  2. Request DTC by Status.

Is DTC P0713 displayed?

--

Go to Step 4

Go to Step 5

4
  1. Turn OFF the ignition.
  2. Measure the resistance between the vehicle harness and transmission fluid temperature (TFT) sensor. Refer to Transmission Fluid Temperature Sensor Inspection .
  3. Disconnect the TCM connector and measure the resistance between terminal A11 and A12.

Is the measurement within the specified values?

10°C (50°F)

5.80-7.09 KΩ

110°C (230°F)

0.231-0.263 KΩ

Go to Step 6

Go to Step 7

5

Repair the temporary connection failure of the connector. Refer to Wiring Harness and Connector Inspection Diagnosis .

Did you complete the repair?

--

System OK

--

6
  1. Inspect for damage between the vehicle wiring harness connector and the transmission control module (TCM).
  2. Inspect the connector. Refer to Wiring Harness and Connector Inspection Diagnosis .
  3. Inspect the connection condition between the connectors.

Is the connection condition OK?

--

Go to Step 8

Go to Step 5

7
  1. Inspect for damage between the vehicle harness and the TFT sensor.
  2. Disconnect the transaxle harness connect and measure the resistance between the TFT sensor connector terminal 1 and 6.

Is the measurement within the specified values?

10°C (50°F)

5.80-7.09 KΩ

110°C (230°F)

0.231-0.263 KΩ

Go to Step 9

Go to Step 10

8
  1. Replace the TCM. Refer to Transmission Control Module Replacement .
  2. Perform the reproducing test under user condition after confirming no DTC.

Is DTC displayed?

--

Go to Step 2

System OK

9
  1. Inspect for damage of the vehicle wiring harness or between connectors.
  2. Test the continuity and short circuit for the vehicle wiring harness and inspect the connection condition between the connectors. Refer to Wiring Harness and Connector Inspection Diagnosis .

Is the condition OK?

--

System OK

Go to Step 5

10
  1. Inspect for damage of the T/M wire or between the connectors of the TFT sensor.
  2. Inspect the fluid temperature. Refer to Transmission Fluid Temperature Sensor Inspection .

Is the condition found?

--

Go to Step 12

Go to Step 11

11
  1. Inspect for damage of the transaxle harness.
  2. Test the continuity and short circuit for the transaxle harness and inspect the connection condition between the connectors. Refer to Wiring Harness and Connector Inspection Diagnosis .

Is the condition OK?

--

System OK

Go to Step 5

12

Replace the TFT sensor. Refer to Transmission Fluid Temperature Sensor Inspection .

Did you complete the repair?

--

System OK

--

DTC P0713 European and N. American Emissions

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0713 Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage

Conditions for Setting the DTC
    • The transmission control module (TCM) detects that the analog-to-digital (A/D) value of the transmission fluid temperature (TFT) sensor signal is less than 15 and the minimum A/D value is more than 943, when it is past 15 minutes after ignition ON--A/D value 943:4.7 volts.
    • After one occurrence of above detection
    • Gear selector position is except park and neutral
    • Engine revolution is 400 RPM or greater

Action Taken When the DTC Sets
    • The TCM will request the illumination of the malfunction indicator lamp (MIL) and store the DTC when the TCM detects a failure on the first ignition cycle.
    • The TCM judges the temperature of the transmission fluid is 200°C (392°F).
    • No lockup control
    • No 4th gear
    • No self-learning control
    • No timing solenoid control N-D

Conditions for Clearing the DTC
    • The TCM turns OFF the MIL when no further failures are detected on the next ignition cycle.
    • The scan tool can clear the DTC from the TCM history.
    • The TCM clears the DTC from the TCM history memory after 40 consecutive ignition cycles without fault.
    • The TCM detects the temperature of the transmission fluid is between 0-150°C for 10 seconds continuously.

Cause of Failure
    • The wiring harness or connector between the TFT sensor and the TCM
    • The TFT sensor
    • The TCM

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check - Automatic Transmission?

--

Go to Step 2

Go to Diagnostic System Check - Automatic Transmission

2
  1. Turn OFF the ignition.
  2. Install the scan tool.
  3. With the engine OFF, turn the ignition switch to the ON position.
  4. Select Store Freeze Frame/Failure Records from the DTC Information menu.
  5. Store Freeze Frame/Failure Records.
  6. Select Clear DTC Information from the DTC Information menu.
  7. Clear the DTC information.
  8. Perform 2 vehicle drive cycles.

Is the malfunction indicator lamp (MIL) ON?

--

Go to Step 3

Go to Step 5

3
  1. Select Request DTC by Status from the DTC Information menu.
  2. Request DTC by Status.

Is DTC P0713 displayed?

--

Go to Step 4

Go to Step 5

4
  1. Turn OFF the ignition.
  2. Measure the resistance between the vehicle harness and the transmission fluid temperature (TFT) sensor. Refer to Transmission Fluid Temperature Sensor Inspection .
  3. Disconnect the TCM connector and measure the resistance between terminal A11 and A12.

Is the measurement within the specified values?

10°C (50°F)

5.80-7.09 KΩ

110°C (230°F)

0.231-0.263 KΩ

Go to Step 6

Go to Step 7

5

Repair the temporary connection failure of the connector. Refer to Wiring Harness and Connector Inspection Diagnosis .

Did you complete the repair?

--

System OK

--

6
  1. Inspect for damage between the vehicle wiring harness connector and the transmission control module (TCM).
  2. Inspect the connector. Refer to Wiring Harness and Connector Inspection Diagnosis .
  3. Inspect the connection condition between the connectors.

Is the connection condition OK?

--

Go to Step 8

Go to Step 5

7
  1. Inspect for damage between the vehicle harness and the TFT sensor.
  2. Disconnect the transaxle harness connect and measure the resistance between the TFT sensor connector terminal 1 and 6.

Is the measurement within the specified values?

10°C (50°F)

5.80-7.09 KΩ

110°C (230°F)

0.231-0.263 KΩ

Go to Step 9

Go to Step 10

8
  1. Replace the TCM. Refer to Transmission Control Module Replacement .
  2. Perform the reproducing test under user condition after confirming no DTC.

Is DTC displayed?

--

Go to Step 2

System OK

9
  1. Inspect for damage of the vehicle wiring harness or between the connectors.
  2. Test the continuity and short circuit for the vehicle wiring harness, and inspect the connection condition between the connectors. Refer to Wiring Harness and Connector Inspection Diagnosis .

Is the condition OK?

--

System OK

Go to Step 5

10
  1. Inspect for damage of the T/M wire or between the connectors of the TFT sensor.
  2. Inspect the fluid temperature. Refer to Transmission Fluid Temperature Sensor Inspection .

Is the condition found?

--

Go to Step 12

Go to Step 11

11
  1. Inspect for damage of the transaxle harness.
  2. Test the continuity and short circuit for the transaxle harness and inspect the connection condition between the connectors. Refer to Wiring Harness and Connector Inspection Diagnosis .

Is the condition OK?

--

System OK

Go to Step 5

12

Replace the TFT sensor. Refer to Transmission Fluid Temperature Sensor Inspection .

Did you complete the repair?

--

System OK

--