GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2006 🢒 Wave 🢒 DTC 🢒 DTC P0420

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptor

DTC P0420: Catalyst System Low Efficiency

Circuit/System Description

A 3-way catalytic converter (TWC) controls emissions of hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx). The catalyst within the converter promotes a chemical reaction, which oxidizes the HC and the CO that are present in the exhaust gas. This process converts the HC and the CO into water vapor and carbon dioxide (CO2), and reduces the NOx, converting the NOx into nitrogen. The catalytic converter also stores oxygen. The engine control module (ECM) monitors this process by using a heated oxygen sensor (HO2S) that is in the exhaust stream after the TWC. The HO2S 2 produces an output signal that the ECM uses to calculate the oxygen storage capacity of the catalyst. This indicates the ability of the catalyst to convert the exhaust emissions efficiently. The ECM monitors the efficiency of the catalyst by allowing the catalyst to heat, then wait for a stabilization period while the engine is idling. The ECM then adds and removes fuel while monitoring the HO2S 2. When the catalyst is functioning properly, the HO2S 2 response to the extra fuel is slow compared to the response of the HO2S 1, which is located before the TWC. When the HO2S 2 response is near that of the HO2S 1, the oxygen storage capability and efficiency of the catalyst may be degraded below an acceptable threshold.

Conditions for Running the DTC
    • DTCs P0030, P0036, P0107, P0108, P0112, P0113, P0117, P0118, P0122, P0123, P0131, P0132, P0133, P0137, P0138, P0140, P0171, P0172, P0300, P0335, P0336, P0337, P0341, P0342, P0400-P0406, P0501, P0510 and U0101 are not set.
    • The engine has been running for more than 16 minutes.
    • The engine speed is between 2,016-2,880 RPM.
    • The vehicle speed is between 65-75 km/h (40-47 mph).
    • The engine coolant temperature (ECT) is more than 70°C (158°F).
    • The barometric pressure (BARO) is more than 70 kPa.
    • The TWC calculated temperature is between 350-950°C (662-1,742°F).
    • The vehicle is operating in Closed Loop.
    • The air flow into the engine is between 23-53 kg/h and is not changing more than 10 kg/h.

Conditions for Setting the DTC

The ECM determines that the efficiency of the catalyst has degraded below a calibrated threshold.

Action Taken When the DTC Sets

DTC P0420 is a Type B DTC

Conditions for Clearing the DTC

DTC P0420 is a Type B DTC

Diagnostic Aids

Inspect for the following conditions, which may cause a catalytic converter to degrade:

    • An engine misfire
    • High engine oil or high coolant consumption
    • Retarded spark timing
    • A weak or poor spark
    • A lean fuel mixture
    • A rich fuel mixture
    • A damaged oxygen sensor or wiring harness
    • If the condition is determined to be intermittent, refer to Testing for Intermittent Conditions and Poor Connections .

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Engine Control Module Connector End Views
    •  Engine Controls Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions
    •  Scan Tool Output Controls

Circuit/System Testing
  1. Verify there are no HO2S or misfire DTCs set.
    2. ⇒If there is an HO2S or misfire DTC set, refer to Diagnostic Trouble Code (DTC) List - Vehicle to diagnosis the applicable DTC, before proceeding with this diagnostic procedure.
  2. Verify the following conditions do not exist with the catalytic converter:
    3. • Dents
    • A severe discoloration caused by excessive temperatures
    • Road damage
    • An internal rattle caused by damaged catalyst substrate
    • Restrictions
         ⇒If a condition is found, replace the catalytic converter.
  3. Verify the following conditions do not exist with the exhaust system:
    4. • Leaks
    • Physical damage
    • Loose or missing hardware
    • Properly torqued HO2S
         ⇒If a condition is found, repair the exhaust system.
  4. Verify the following conditions do not exist with the HO2S 2:
    5. • A grounded wiring harness
    • Damage
         ⇒If a condition is found, replace the HO2S 2.
  5. If no physical condition is detected and the HO2S 2 is as active as the HO2S 1 after operating the engine at 1,500 RPM for 1 minute and then returning to a stabilized idle, then replace the catalytic converter.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Heated Oxygen Sensor 2 Replacement
    •  Catalytic Converter Replacement