Front Case Half
- Clean the front case half in cleaning solvent
and air dry.
Notice: Refer to Machined Surface Damage Notice in the Preface section.
- Remove the sealer from the case sealing surfaces.
- Inspect the case for being broken or cracked.
- Inspect the front output shaft front bearing bore (8) for the following
conditions:
- Inspect the input shaft bearing bore (5) for the following conditions:
- Replace the front case half if any of the above conditions are found.
- Inspect the sealing surfaces (1) for damage.
- Repair small scratches or nicks with a soft stone.
- Inspect the front case to transmission case mounting surface for damage.
- Inspect the case threaded bolt holes (2) for damage.
- Repair any damaged threads.
- Inspect the transmission to transfer case studs (4) for damage.
- Replace any damaged studs. Refer to
Transfer Case Assemble
.
- Inspect the retaining ring (3) of the annulus gear to ensure it
is properly seated.
- Inspect the annulus gear (6) for the following conditions:
| • | Debris embedded in the root of the teeth |
- Replace the front case half if the annulus gear is damaged.
- Inspect the control actuator lever shaft bearing and seal (7)
for the following:
- Replace the control actuator lever shaft bearing if it is faulty. Refer
to
Transfer Case Disassemble
and
Transfer Case Assemble
.
- Inspect the location pins for being loose or missing.
- Repair or replace any damaged location pins.
- Inspect the front output shaft front bearing and the input shaft bearing
for the following conditions:
- Replace the bearings if any of the above conditions are found. Refer to
Transfer Case Disassemble
and
Transfer Case Assemble
.
Rear Case Half
- Clean the rear case half in cleaning solvent
and air dry.
Notice: Refer to Machined Surface Damage Notice in the Preface section.
- Remove the sealer from the case sealing surfaces.
- Inspect the case for being broken or cracked.
- Replace the case if it is broken or cracked.
- Inspect the sealing surfaces (1) for damage.
- Repair small scratches or nicks with a soft stone.
- Inspect the case threaded bolt holes for damage.
- Repair any damaged threads.
- Inspect the oil pump wear sleeve (5) for wear or damage.
- Replace the oil pump retainer if faulty.
- Inspect the front output shaft rear bearing (4) for the following
conditions:
- Replace the front output shaft rear bearing if any of the above conditions
are found. Refer to
Transfer Case Disassemble
and
Transfer Case Assemble
.
- Inspect the rear output shaft bearing for the following conditions:
- Inspect for a spun bearing bore for the rear output shaft rear bearing.
- Replace the case if a bearing has spun.
- Inspect the retaining ring (2) for the rear output shaft rear bearing
for being bent or twisted.
- Replace a faulty retaining ring.
- Inspect the rear output shaft bushing (3) for scoring or wear.
- Replace a faulty rear output shaft bushing. Refer to
Transfer Case Disassemble
and
Transfer Case Assemble
.
Oil Pump
- Clean
the oil pump suction pipe, with the screen, in cleaning solvent and air dry. Do not
remove the screen from the pipe.
- If the screen is embedded with debris, replace the suction pipe assembly.
- Inspect the oil pump for free movement.
- Replace the oil pump if there is any binding. Do not disassemble the oil
pump. The oil pump is serviced as a unit.
Rear Output Shaft
- Clean the rear output shaft in cleaning
solvent.
- Clean the rear output shaft oil galleries (1) and air dry.
Important: Do not attempt to smooth any roughness in
the bearing journals.
- Inspect the input gear pilot bearing surface (2) and the clutch housing
bearing surface (3) for the following conditions:
- Inspect the rear output shaft splines (4) for damage or excessive
wear. Witness marks at the location of the gears are normal.
- Replace the rear output shaft if any of the above conditions are found.
Clutch Components
- Do not clean the inner clutch discs (1)
in cleaning solvent.
- Inspect the inner clutch discs (1), with the friction material,
for the following conditions:
| • | Grooved or scored friction material |
- Inspect the outer clutch discs (2) steel plates for being worn
or warped. If the discs show wavey wear marks, the discs are faulty.
- Replace the clutch discs if any of the above conditions are found.
- Clean the clutch pressure plate (3),
the clutch pressure plate bearing (2) and the clutch bearing inner support (1)
in cleaning solvent and air dry.
- Inspect the pressure plate bearing (2) for the following conditions:
- Replace the pressure plate bearing if it is damaged or worn.
- Inspect the clutch pressure plate (3) for wear or damage.
- Replace a faulty clutch pressure plate.
- Inspect the clutch pressure plate bearing hub (1) for wear or damage.
- Replace a faulty clutch pressure plate bearing hub.
- Inspect for a damaged clutch spring (4).
- Replace a faulty clutch spring.
- Clean the clutch housing, with the bearing,
in cleaning solvent.
- Air dry and ensure all solvent is removed from the bearing.
- Inspect the bearing for wear or damage.
- Replace the clutch housing bearing if faulty. Refer to
Transfer Case Disassemble
and
Transfer Case Assemble
.
- Inspect the clutch housing disc teeth for excessive wear. Excessive wear
can be identified by the steps in the teeth, which prevents the clutch disc from moving
freely.
- Replace the clutch housing if the clutch disc teeth cannot be deburred.
- Clean the clutch hub in cleaning solvent and air dry.
- Inspect the clutch disc surface (3) for excessive wear, warpage,
or grooves.
- Inspect the rear output shaft to the clutch inner hub splines (1)
for excessive looseness.
- Inspect the clutch hub teeth (4) for excessive wear. Steps in the
teeth can identify excessive wear, which prevents the clutch disc from moving freely.
- Inspect the clutch pressure plate tab slots (2) for excessive wear.
- Replace the clutch hub if any of the above conditions are found.
High/Low Planetary Carrier
- Clean the high/low planetary carrier in
cleaning solvent. Do not disassemble the planetary carrier.
- Air dry and ensure all cleaning solvent is removed from the bearings
in the planetary gears (3). Do not spin the planetary gears with compressed
air.
- Inspect the planetary gears for chipped teeth.
- Inspect the planetary gears for debris embedded in the root of the teeth.
- Inspect for a washer (4) being on each side of the planetary gears.
- Inspect the low range teeth (1) for damage or excessive wear.
- Inspect the thrust washer surface (2) for scoring or excessive
wear.
- Replace the high/low planetary carrier if any of the above conditions
are found.
Drive Chain and Sprockets
- Clean the drive chain (1), drive
sprocket (3), and driven sprocket (2) in cleaning solvent and air dry.
- Inspect the drive chain (1) for the following conditions:
| • | Debris embedded in the links |
- Replace the chain if any of the above conditions are found.
- Inspect the driven sprocket (2) and the drive sprocket (3)
for the following conditions:
| • | Excessive worn gear surfaces, slight wear marks are normal |
| • | Debris embedded in the root of the teeth |
- Replace the sprocket if any of the above conditions are found. The chain
and sprockets may be replaced separately.
Front Output Shaft
- Clean the front output shaft in cleaning
solvent and air dry.
- Inspect the teeth on the speed sensor reluctor wheel (2) for damage.
- Replace the speed sensor reluctor wheel if it is damaged. Refer to
Transfer Case Disassemble
and
Transfer Case Assemble
.
- Inspect the front output shaft rear bearing race (1) for the following
conditions:
- Inspect the front output shaft splines (3) for damage.
- Inspect the front output shaft seal surface (4) for wear or roughness.
- Replace the front output shaft if any of the above conditions are found.
Input Gear
- Clean the input gear, with pilot bearing,
in cleaning solvent.
- Air dry and ensure all solvent is removed from the pilot bearing.
- Inspect the pilot bearing (1) for the following conditions:
- Replace the input gear pilot bearing if any of the above conditions are
found. Refer to
Transfer Case Disassemble
and
Transfer Case Assemble
.
- Inspect the input gear engagement teeth (2) for chips.
- Inspect the input gear for broken or damaged planetary teeth (3).
- Inspect the input gear for debris embedded in the root of the teeth.
- Inspect the input gear seal surface (4) for pitting or excessive
wear.
- Replace the input gear if any of the above conditions are found.
Shift System Components
- Clean
the following shift system components in cleaning solvent and air dry:
| • | The high/low shift fork (1) |
| • | The shift fork shaft (4) |
| • | The control actuator lever shaft (5) |
- Inspect the shift fork shaft for straightness (4).
- Replace the shift fork shaft if it is not straight.
- If 1st design, inspect the pads (2)
on the shift fork for wear.
- If 2nd design, inspect the pads (3) on the shift fork for wear
or breakage.
- Replace the worn or broken pads.
- Inspect the roller (1) on the shift fork for wear, or for being
broken or bent.
- Replace the shift fork if the roller is worn.
Important: Do not disassemble the shift fork assembly.
The shift fork is serviced as a complete assembly.
- Inspect the following components of the shift fork assembly for wear or damage:
- Inspect
the clutch lever roller (2) for the following conditions:
- Inspect the clutch lever assembly for worn wear pads (1).
- Inspect the clutch lever assembly for wear at the pivot pin holes (3).
- Replace the clutch lever assembly if the above conditions are found.
- Inspect the range sleeve for chipped or
excessive worn teeth (1).
- Inspect the shift fork collar (2) on the range sleeve for wear.
- Inspect the inner splines (3) of the range sleeve for excessive
looseness on the rear output shaft.
- Replace the range sleeve if the above conditions are found.
- Inspect the shift fork roller slot (1)
on the control actuator lever shaft for wear or roughness.
- Inspect the bearing (2) and the seal surface on the control actuator
lever shaft for the following conditions:
- Inspect the clutch lever cam lobes (3) on the control actuator
lever shaft for wear or roughness.
- Replace the control actuator lever shaft if any of the above conditions
are found.
