1

3-5 Reverse Clutch Backing Plate Retaining Ring

2

3-5 Reverse Clutch Backing Plate

3

3-5 Reverse Clutch Plate Assembly (Quantity: 4)

4

3-5 Reverse Clutch Plate (Quantity: 4)

5

3-5 Reverse Clutch (Waved) Plate

6

3-5 Reverse Clutch Apply Ring

7

1-2-3-4 Clutch Backing Plate Retaining Ring

8

1-2-3-4 Clutch Backing Plate

9

1-2-3-4 Clutch Plate Assembly (Quantity: 5)

10

1-2-3-4 Clutch Plate (Quantity: 5)

11

1-2-3-4 Clutch (Waved) Plate

1

1-2-3-4 Clutch Piston Dam Retaining Ring

Notice: Use care when compressing the 1-2-3-4 clutch spring and dam assembly. Compressing the dam assembly too much may damage it.

Notice: Refer to Retaining Ring Reuse Notice in the Preface section.

Special Tool

J 38734 Intermediate Spring Compressor Adapter

2

1-2-3-4 Clutch Piston Dam Assembly

3

1-2-3-4 Clutch Spring

4

1-2-3-4 Clutch Piston

Tip

Preliminary Procedures

1. Install the 1-2-3-4 and 3-5 reverse clutch housing assembly onto the torque converter (with fluid pump) housing assembly.
2. Apply hand pressure on the 1-2-3-4 clutch piston housing while applying compressed air to the apply passage in order to unseat the 3-5 reverse clutch piston.

1

1-2-3-4 Clutch Piston Housing Retaining Ring

Notice: Refer to Retaining Ring Reuse Notice in the Preface section.

Special Tool

DT 47867 Adjustable Clutch Spring Compressor

2

1-2-3-4 Clutch Piston Housing

3

3-5 Reverse Clutch Spring

4

3-5 Reverse Clutch Piston

Tip
It may be necessary to turn the housing assembly upside down and carefully tap the housing against a flat surface in order to release the piston.

Notice: Refer to Seal Reuse Notice in the Preface section.

Tip
Lubricate all seals with automatic transmission fluid (ATF) prior to installation.

1

1-2-3-4 Clutch Piston Seal

2

3-5 Reverse Clutch Piston Dam (O-Ring) Seal

3

3-5 Reverse Clutch Piston Inner Seal

4

1-2-3-4 Clutch Piston Housing

5

3-5 Reverse Clutch Piston Outer Seal

6

3-5 Reverse Clutch Piston

7

1-2-3-4 Clutch Piston Inner Seal

Notice: Do not install a NEW 1-2-3-4 clutch piston inner seal yet. A special tool used to install the 1-2-3-4 clutch piston housing retaining ring may damage the seal if the seal is installed prior to installing the retaining ring. Refer to 3-5 Reverse Clutch Piston Installation.

8

1-2-3-4 Clutch Piston Housing Seal

9

1-2-3-4 Clutch Piston Housing Seal

1

3-5 Reverse Clutch Piston

2

3-5 Reverse Clutch Spring

Notice: Ensure the clutch spring is centered on the piston with the tabs facing up. Failure to do so may cause damage to the clutch assembly.

3

1-2-3-4 Clutch Piston Housing

4

1-2-3-4 Clutch Piston Housing Retaining Ring

Notice: Before using the DT 47782-2, push the retaining ring over the DT 47782-1 by hand so that the ring is positioned below the tapered area of the DT 47782-1. If the ring is positioned above the tapered area when it is being installed, the ring will become lodged between both tools and damage to the tools, retaining ring, and piston housing will result.

Notice: Refer to Retaining Ring Reuse Notice in the Preface section.

Notice: Push the retaining ring down over the cone until the ring seats firmly in the retaining ring groove. The retaining ring will make a distinctive click sound when it seats. Failure to properly seat the retaining ring may cause damage to the 3-5 reverse clutch assembly.

Tip
Use a screwdriver in order to verify the retaining ring is fully seated into the groove. It may appear as though the retaining ring is not fully seated, since the groove is shallow by design. However, this shallow interface is normal.

Special Tools

5

1-2-3-4 Clutch Piston Inner Seal

Notice: Install a NEW seal and orientate as shown. Failure to do so may cause internal transmission leaks and damage to the transmission.

1

1-2-3-4 Clutch Piston

2

1-2-3-4 Clutch Spring

Notice: Ensure the clutch spring is centered on the piston with the tabs facing up. Failure to do so may cause damage to the clutch assembly.

3

1-2-3-4 Clutch Piston Dam Assembly

Tip
Lubricate the inner and outer surfaces of the dam assembly with ATF in order to ease installation into the piston. Install the tabs facing up.

4

1-2-3-4 Clutch Piston Dam Retaining Ring

Notice: Use care when compressing the 1-2-3-4 clutch spring and dam assembly. Compressing the dam assembly too much may damage it.

Notice: Refer to Retaining Ring Reuse Notice in the Preface section.

Special Tool

J 38734 Intermediate Spring Compressor Adapter

1

1-2-3-4 Clutch (Waved) Plate

Notice: Ensure an opening between the external splines of the waved plate is centered over the missing snap ring groove punch in the housing. Failure to do so may cause damage to the clutch assembly.

2

1-2-3-4 Clutch Plate (Quantity: 5)

Notice: Ensure all clutch plates are centered in the housing. When installing the first steel clutch plate, ensure an opening between the external splines is centered over the missing snap ring groove punch in the housing. Align the external splines of each remaining steel clutch plate with the first steel clutch plate. Failure to do so may cause damage to the clutch assembly.

3

1-2-3-4 Clutch Plate Assembly (Quantity: 5)

4

1-2-3-4 Clutch Backing Plate

Notice: Align the external splines of the backing plate with the external splines of the steel clutch plates. Failure to do so may cause damage to the clutch assembly.

5

1-2-3-4 Clutch Backing Plate Retaining Ring

Notice: Depending on the housing configuration, align the retaining ring gap with the missing snap ring groove punch in the housing or the offset punch in the housing. Failure to do so may cause damage to the clutch assembly.

Tip
After the retaining ring is installed, determine clutch piston travel in order to verify if the correct selective retaining ring is being used. Refer to 1-2-3-4 Clutch Backing Plate Retaining Ring Measurement .

1

3-5 Reverse Clutch Apply Ring

Notice: Ensure apply ring legs are positioned into the 3-5 reverse clutch piston. Failure to do so may cause damage to the 3-5 reverse clutch assembly.

2

3-5 Reverse Clutch (Waved) Plate

3

3-5 Reverse Clutch Plate (Quantity: 4)

4

3-5 Reverse Clutch Plate Assembly (Quantity: 4)

5

3-5 Reverse Clutch Backing Plate

6

3-5 Reverse Clutch Backing Plate Retaining Ring

Notice: Depending on the housing configuration, align the retaining ring gap with the missing snap ring groove punch in the housing or the offset punch in the housing. Failure to do so may cause damage to the clutch assembly.

Tip
After the retaining ring is installed, determine clutch piston travel in order to verify if the correct selective retaining ring is being used. Refer to 3-5 Reverse Clutch Backing Plate Retaining Ring Measurement .

1

3-5 Reverse Clutch Bearing

Notice: Install the NEW bearing assembly with the seal side up. Improper installation of the bearing may cause damage to the transmission.

Notice: Do not reuse the bearing. Install a NEW bearing. Reusing an old bearing may cause damage to the transmission.

Specification
Install the bearing flush to 0.3 mm below the thrust surface.

Special Tools