GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saab 🢒 2007 🢒 9-7x 🢒 DTC 🢒 DTC B3802

Circuit Description

The body control module (BCM) monitors the park lamp switch signal circuit and the headlamp switch headlamps on signal circuit in order to determine when the park lamps and headlamps should be illuminated. When the headlamp switch is turned to PARK, the BCM senses that the park lamp switch signal circuit is grounded and the headlamps switch headlamps on signal circuit is open. The BCM will then energize the park lamp relay illuminating the park lamps. When the headlamp switch is turned to HEAD, the BCM senses that the park lamp switch signal circuit and the headlamp switch headlamps on signal circuit are grounded. The BCM will then energize the park lamp relay and headlamp driver module (HDM) illuminating the park lamps and headlamps.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B3802 Park Lamps Request Circuit

Conditions for Running the DTC

The battery voltage must be between 9-16 volts.

Conditions for Setting the DTC

When the BCM receives the headlamps ON signal request without a park lamp ON signal request from the headlamp switch.

Action Taken When the DTC Sets

The park lamps will not operate or the headlamps will illuminate without the park lamps.

Conditions for Clearing the MIL/DTC
    • This DTC will clear on current status after the condition for setting the fault is corrected.
    • A history DTC will clear after 100 consecutive ignition cycles without a fault present.
    • History and current DTCs can be cleared using a scan tool.

Step

Action

Yes

No

Schematic Reference: Exterior Lights Schematics

Connector End View Reference: Lighting Systems Connector End Views , Secondary/Configurable Control Connector End Views , or Data Communication Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Turn the headlamp switch to HEAD.
  4. With a scan tool, observe the Park Lamp Switch parameter in the body control module (BCM) data list.

Does the scan tool display Active?

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 3

3

Test the signal circuit of the park lamp switch for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct a condition?

Go to Step 10

Go to Step 4

4

Test the headlamp switch headlamps on signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct a condition?

Go to Step 10

Go to Step 5

5
  1. Disconnect the headlamp multifunction switch.
  2. Turn the headlamp switch to the HEAD position.
  3. Test for continuity between the ground terminal and the park lamp switch signal terminal of the headlamp multifunction switch. Refer to Circuit Testing .
  4. Test for continuity between the ground terminal and the headlamp switch headlamps on signal terminal of the headlamp multifunction switch. Refer to Circuit Testing .

Is continuity present?

Go to Step 6

Go to Step 7

6

Inspect for poor connections at the harness connector of the BCM. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 8

7

Inspect for poor connections at the harness connector of the headlamp multifunction switch. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 9

8

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 10

--

9

Replace the headlamp multifunction switch. Refer to Turn Signal Multifunction Switch Replacement .

Did you complete the replacement?

Go to Step 10

--

10
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK