Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B2580 00: Headlamp High Beam Control CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
HDM Relay Fuse B+ | 1 | 1 | -- | -- |
HI HEADLAMP relay B+ | 2 | 2 | -- | -- |
IGN COILS Relay Fuse B+ | 2 | 2 | -- | -- |
DRL Defeat Switch Signal | 3 | 3 | 3 | -- |
Headlamp High Beam Switch Signal | 4 | 4 | 4 | -- |
Headlamp Flash to Pass Switch Signal | 4 | 4 | 4 | -- |
Headlamp ON Switch Signal | 3 | 3 | 3 | -- |
Low Beam Headlamp Relay Control | B2575 00 | B2575 00 | B2575 00 | -- |
Headlamp ON Indicator Control | B3802 00 | 3 | 3 | -- |
High Beam Headlamp Relay Control | B2580 00 | B2580 00 | B2580 00 | -- |
Low Beam Headlamp Control | 1 | 1 | 1 | -- |
High Beam Headlamp Control | 2 | 2 | 2 | -- |
Headlamp ON Indicator Low Reference | 3 | 3 | 3 | -- |
HDM Relay Ground | -- | 1 | -- | -- |
Headlamp Switch Ground | -- | 3 | -- | -- |
Turn Signal/Multifunction Switch Ground | -- | 4 | -- | -- |
Left Headlamp Ground | -- | 1 | -- | -- |
Right Headlamp Ground | -- | 1 | -- | -- |
1. Headlamp Malfuntion - Low Beam 2. Headlamp Malfuntion - High Beam 3. Headlamp Switch Malfunction 4. Turn Signal/Multifunction Switch Malfunction | ||||
Circuit/System Description
The HDM and high beam relay receive battery voltage directly from the battery. The BCM supplies a 100% duty cycle PWM ground signal to the HDM for automatic low beam headlamp control and normal low beam headlamp operation. The BCM also supplies ground to the high beam relay coil for high beam headlamp operation. When the driver places the headlamp switch in the HEADLAMP position and the dimmer switch is in the low beam position, the HDM switches to full output sending current flow through the left and right low beam headlamp fuses to both low beam headlamps. The dimmer switch sends a ground signal to the BCM in the high beam position and a momentary ground signal in the flash-to-Pass (FTP) position from G102 to deactivate the low beam headlamps and activate the high beam headlamps. With the headlamps in the low beam position, the high beams may be momentarily turned on or flashed by activating the FTP portion of the switch.
Conditions for Running the DTC
The battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
| • | When the BCM receives a high beam headlamp request the high beam headlamp relay control circuit is shorted to voltage. |
| • | When the BCM is not receiving a high beam headlamp request the high beam headlamp relay control circuit is open or shorted to ground. |
Action Taken When the DTC Sets
The high beam headlamps are inoperative or always on.
Conditions for Clearing the DTC
| • | This DTC will clear on current status after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the HI HEADLAMP relay.
- Verify a test lamp does not illuminate between the control circuit terminal 87 and B+.
- Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 85 and ground.
- Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
- Connect a test lamp between the relay control circuit terminal 86 and B+.
- Operate the high beam headlamps ON and OFF. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, replace the HI HEADLAMP relay.
| ⇒ | If the test lamp illuminates, test the control circuit for a short to voltage. |
| ⇒ | If the test lamp does not illuminate,test the B+ circuit for a short to ground or an open/high resistance. |
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for BCM replacement, programming, and setup
