Steering Knuckle Replacement RWD

Special Tools

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation.
3. Remove the wheel hub and bearing. Refer to Front Wheel Hub, Bearing, and Seal Replacement.
4. Remove and discard the outer tie rod retaining nut.



5. Disconnect the outer tie rod from the steering knuckle using J 24319-B .



6. Remove the brake hose bracket retaining bolts.
7. Remove the brake hose bracket from the steering knuckle.



8. Disconnect the ABS wheel speed sensor wiring harness bracket from the steering knuckle.



9. Remove and discard the upper control arm to the steering knuckle pinch bolt and nut.
10. Disconnect the upper control arm from the steering knuckle.



11. Remove and discard the lower ball joint retaining nut.



12. Remove the steering knuckle from the lower control arm using J 43631 .
13. Remove the steering knuckle from the vehicle.

1. Install the steering knuckle to the lower control arm.

Caution: Refer to Fastener Caution in the Preface section.

2. Install a new lower ball joint retaining nut and tighten to 110 N·m (81 lb ft).



3. Connect the upper control arm to the steering knuckle.
4. Install a new upper control arm pinch bolt and nut and tighten the bolt to 40 N·m (30 lb ft).



5. Connect the ABS wheel speed sensor wiring harness bracket to the steering knuckle.



6. Install the brake hose bracket to the steering knuckle.
7. Install the brake hose bracket retaining bolts and tighten to 10 N·m (89 lb in).



8. Install the outer tie rod to the steering knuckle.
9. Install the new outer tie rod retaining nut and tighten to 60 N·m (44 lb ft).
10. Install the wheel hub and bearing. Refer to Front Wheel Hub, Bearing, and Seal Replacement.
11. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation.
12. Lower the vehicle.
13. Check the front wheel alignment. Refer to Wheel Alignment Specifications.

Steering Knuckle Replacement 4WD

Special Tools

1. Remove the tire and wheel center cap.
2. Remove the drive axle nut.



3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
4. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation.
5. Remove the wheel hub and bearing. Refer to Front Wheel Hub, Bearing, and Seal Replacement.
6. Remove and discard the outer tie rod retaining nut.



7. Disconnect the outer tie rod from the steering knuckle using J 24319-B .



8. Remove the brake hose bracket retaining bolts.
9. Remove the brake hose bracket from the steering knuckle.



10. Remove and discard the upper control arm to the steering knuckle pinch bolt and nut.
11. Disconnect the upper control arm from the steering knuckle.



12. Remove and discard the lower ball joint retaining nut.



13. Remove the steering knuckle from the lower control arm using J 43631 .
14. Remove the steering knuckle from the vehicle.

1. Install the steering knuckle to the lower control arm.

Caution: Refer to Fastener Caution in the Preface section.

2. Install a new lower ball joint retaining nut and tighten to 110 N·m (81 lb ft).



3. Connect the upper control arm to the steering knuckle.
4. Install a new upper control arm pinch bolt and nut and tighten the bolt to 40 N·m (30 lb ft).



5. Install the brake hose bracket to the steering knuckle.
6. Install the brake hose bracket retaining bolts and tighten to 10 N·m (89 lb in).



7. Install the outer tie rod to the steering knuckle.
8. Install the new outer tie rod retaining nut and tighten to 60 N·m (44 lb ft).



9. Install the wheel hub and bearing. Refer to Front Wheel Hub, Bearing, and Seal Replacement.
10. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation.
11. Lower the vehicle.
12. Install the drive axle nut and tighten to 140 N·m (103 lb ft).
13. Check the front wheel alignment. Refer to Wheel Alignment Specifications.